490276

Roblin Palma Manual

11
Zoom out
Zoom in
Previous page
1/52
Next page
9
The above assumes our 150 mm (6 INS) ducting is being installed. Please note ducting components and
ducting kits are optional accessories and have to be ordered, they are not automatically supplied
with the chimney hood.
IN THE EXTRACTION MODE:
a. Place the anti-backow ats item 8 over the round outlet item 6, the telescopic duct and connect the
ducting 150mm (6 INS) over the round outlet on top of the canopy and secure the connections with
appropriate clamping rings or adhesive tape (Fig. 6).
b. Remove the grease lters (see paragraph Maintenance) Fig. 5 being sure that the connector of the
mains cable is correctly inserted in the socket placed on the sides of the fan. Before tting the chimney
to the canopy make the electrical connection as described in the section titled ELECTRICAL. When
the electrical connection has been made, test the lights and the fan motor.
c. Each chimney stack consists of two sections. Encase the upper section in the telescopic bottom sec-
tion (Fig. 1 - item 7a & b) by making it exceed at least 150 mm, maintain it in this position with an
adhesive tape (in order to avoid scratches between the 2 sections). Place slightly the chimney on
the canopy and t the upper sections by expanding the chimneys to allow them to clamp around the
bracket item 2 and secure the chimney stacks to the brackets using the two M4 screws item 12c
provided. Attention scratches risk on the junction line of the canopy with the lower chimney.
Not remove the lm from the canopy before the complete tting of the chimney.
d. Fit the 3 deectors Item 9.
IN THE RECIRCULATION MODE:
a. Fit the recirculation spigot R onto the upper chimney wall bracket using the same xing screws (Fig.
2 item 2).
b. Connect the ducting 150mm (6 INS) not provided between motors item 6 and the recirculation spigot
and secure the connections with appropriate clamping rings or adhesive tape.
c. Remove the grease lters (see paragraph Maintenance) Fig. 5 being sure that the connector of the
feeding cable is correctly inserted in the socket placed on the side of the fan. Before tting the chimney
to the canopy make the electrical connection as described in the section titled ELECTRICAL. When
the electrical connection has been made, test the lights and the fan motor.
d. Insert the charcoal lter into the base of the motor housing and secure the lter with two metal secur-
ing straps item A as illustrated in Fig. 4.
e. Each chimney stack consists of two sections. Encase the upper section in the telescopic bottom
section (Fig. 1 - item 7a & b) by making it exceed at least 150 mm, maintain it in this position with
an adhesive tape (in order to avoid scratches between the 2 sections). Place slightly the chimney
on the canopy and t the upper sections by expanding the chimneys to allow them to clamp around
the bracket item 2 and secure the chimney stacks to the brackets using the two M4 screws item 12c
provided. Attention scratches risk on the junction line of the canopy with the lower chimney.
Not remove the lm from the canopy before the complete tting of the chimney.
f. Fit the 3 deectors Item 9.
GB
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Roblin Palma at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Roblin Palma in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info