Manual Roblin Lido (page 12 of 48) (English, German, Dutch, French, Italian, Spanish)

490295

Zoom out

Zoom in

1/48

After 400 hours use, two quick ash of the LED 1 will indicate that you must replace the active charcoal

lter and clean the metal grease lters. (See chapter on ‘Maintenance’).

To reset the 400-hour timer the motor and lights must be switched ‘OFF’.

Push the LED button ‘+’ for 10 seconds.

One ash of the LED lights 1,2,3,4 and 5 = function is switched ‘OFF’.

Two ashes of the LED lights 1,2,3,4 and 5 = function is switched ‘ON’.

Instructions for replacing the active charcoal lter are given in the chapter on ‘Recycling’.

• Pre-set remote control handset

Your cooker hood is supplied with a deactivated remote control receiver. To use the cooker hood with a

remote control re-programme the hood as follows:

Press the LED button (Lighting) ‘1’ while the motor and lights are switched ‘OFF’, until the LED lights 1 will

ash to conrm the programme has been activated :

One ash of the LED lights 1 = function is switched ‘OFF’.

Two ashes of the LED lights 1 = function is switched ‘ON’.

Caution, the remote control handset must be tted with standard LR03-AAA size 1.5V zinc-carbon alkaline

batteries as illustrated Fig. 5. These batteries should give a long life and constant discharge throughout their

life. These batteries must be disposed of properly and could explode if damaged or exposed to heat.

Do not dispose of on re. Dispose of batteries in the appropriate sort container to protect the environ-

ment.

• Setup Process

Modication: How to adjust the internal microprocessor data to suit the type of motor tted to this

appliance and the supply frequency of 50 or 60 Hz..

1 - Disconnect the cooker hood from the mains supply.

2 - Push the button 0/1 MOTOR.

3 - Reconnect the mains supply while pushing the button 0/1 MOTOR for at least 2 seconds.

4 - Release the button 0/1 MOTOR (the Leds ash for about 3 seconds : capacity’s conrmation SETUP

PROCESS).

5 - While the LED is ashing select the motor type used while pushing one of the 5 buttons in accordance

with the following:

BUTTON 0/1 Light : Motor EBM PRO 220-240 V AC 50 Hz / 220 V AC 60 Hz.

BUTTON 0/1 Motor : Motor FABER 8/28 e 8/50 220-240 V AC 50 Hz / 220 V AC 60 Hz.

BUTTON Speed ( - ) : Motor EBM MISTRAL 220-240 V AC 50 Hz / 220 V AC 60 Hz.

BUTTON Speed (+ ) : Motor EBM PRO 220-240 V AC 50 Hz / 220 V AC 60 Hz.

BUTTON Intensive speed : Motor FABER K40-K50 220-240 V AC 50 Hz / 220 V AC 60 Hz.

N.B. : If you have not selected a motor type while the LED is ashing the microprocessor will automatically

select the default motor EBM PRO 220 - 240 V AC 50 Hz / 220 V AC 60 Hz.

5 USEFUL HINTS

• To obtain the best performance it is advisable to switch ‘ON’ the cooker hood a few minutes (in the

boost setting) before you start cooking and you should leave it running for approximately 15 minutes after

nishing.

• IMPORTANT: NEVER DO FLAMBÉ COOKING UNDER THIS COOKER HOOD

• Do not leave frying pans unattended during use as over-heated fat and oil might catch re.

• Do not leave naked ames under this cooker hood.

• Switch ‘OFF’ the electric and gas before removing pots and pans.

• Ensure heating areas on your hotplate are covered with pots and pans when using the hotplate

and cooker hood simultaneously.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Roblin Lido in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1,11 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Roblin Lido Manual

Product: