Manual Roblin Inspiration Slim FX (page 10 of 60) (English, German, Dutch, French, Italian, Spanish)

490307

Zoom out

Zoom in

1/60

or injury and would deem the manufacturers guarantee null and void.

IMPORTANT - The wires in this mains lead are coloured in accordance with the following code :

green / yellow : earth blue : neutral brown : live

As the colours of the wires in the mains lead of this appliance may not correspond with the coloured

markings identifying the terminals in your plug, proceed as follows.

- The wire which is coloured green and yellow must be connected to the terminal in the plug which is

marked with the letter E or by the earth symbol

or coloured green or green and yellow.

- The wire which is coloured blue must be connected to the terminal which is marked with the letter N

or coloured black.

- The wire which is coloured brown must be connected to the terminal which is marked with the letter

L or coloured red.

ATTENTION: Do not forget to use adequate plugs to the support brackets. Enquire after the manu-

facturers. Do an embedding if necessary. The manufacturer accepts no responsibility in case of a

faulty hanging due to the drilling and the setting up of plugs in the ceiling.

1) Unpack the hood parcel.

• FIXING BY THE STRUCTURE : LAYING OUT BEFORE FITTING THE HOOD

2) Mark the centre of the cooking appliance onto the ceiling with a plumb line. Draw the horizontal axes

running parallel to the stove top onto the ceiling as illustrated Fig. 1.

3) To carry out the cutting of embedding in the suspended ceiling (Fig 2a).

4) To mark the centers of different drillings to be carried out on the ceiling. (Fig 2b)

5) Drill the different holes with the appropriate masonry bit :

- The cut-out for the ducting Ø 150 mm in the extraction

mode when ducting runs through the ceiling.

- The mains supply cords.

- The 4 xing holes for Ø 10 mm nuts and bolts.

When xing the cooker hood to a plasterboard ceiling ensure it is reinforced as illustrated in Fig. 3 and

attach using four Ø10mm nuts and bolts; ensuring the bolts as sleeved between the plasterboard and the

joist supports to prevent the ceiling being damaged when the bolts are tightened up.

If the ceiling is concrete, use eight Ø 10 mm steel rawl bolts. Plastic rawl plugs must not be used. Fit the

motor housing (Fig. 4): 4 positions with 90°.

6) To adjust the height of the motor housing: 20 mm of adjustment (Fig. 5).

7) Open the deector ( Fig. 6 Rep. 12) by pushing / unlocking (Fig. 14).

8) To remove the metal lters.

• DUCTING

The hood is more effective when used in the extraction mode (ducted to the outside). When the cooker

hood is ducted to the outside, charcoal lters are not required.

The ducting used must be 150 mm (6 INS), rigid circular pipe and must be manufactured from re retard-

ant material, produced to BS.476 or DIN 4102-B1. Wherever possible utilise rigid circular pipe which has

a smooth interior, rather than the expanding concertina type ducting.

Maximum length of ducting run:

- 4 metres with 1 x 90° bend.

- 3 metres with 2 x 90° bends.

- 2 metres with 3 x 90° bends.

The above assumes our 150 mm (6 INS) ducting is being installed. Please note ducting components and

ducting kits are optional accessories and have to be ordered, they are not automatically supplied with the

chimney hood.

IN THE EXTRACTION MODE:

a- Fit the non-return backow aps C over the round outlet item 6 on top of the canopy while pressing

down until they snap into position, and then connect the ducting 150mm (6 INS) and secure the connec-

tions with appropriate clamping rings or adhesive tape (Fig. 8).

b- Make the electrical connection of the motor as described in the section titled ELECTRICAL.

c- Place the canopy under the motor housing and x it with the screws provided as illustrated in Fig. 10.

Attention: 2 persons are necessary to secure this operation..

d- Connect the electrical plug of the motor cord on the body hood (Fig.7).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Roblin Inspiration Slim FX in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 2,9 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Roblin Inspiration Slim FX Manual

Product: