490315

Roblin Declic 609 Manual

8
Zoom out
Zoom in
Previous page
1/44
Next page
6
GB
green / yellow : earth blue : neutral brown : live
As the colours of the wires in the mains lead of this appliance may not correspond with the coloured
markings identifying the terminals in your plug, proceed as follows.
- The wire which is coloured green and yellow must be connected to the terminal in the plug which is
marked with the letter E or by the earth symbol
or coloured green or green and yellow.
- The wire which is coloured blue must be connected to the terminal which is marked with the letter N
or coloured black.
- The wire which is coloured brown must be connected to the terminal which is marked with the letter
L or coloured red.
ATTENTION: Do not forget to use adequate plugs to the support brackets. Enquire after the manu-
facturers. Do an embedding if necessary. The manufacturer accepts no responsibility in case of a
faulty hanging due to the drilling and the setting up of plugs.
Extractor DECLIC + CONFORT PRO Motor
The installation of the telescopic extractor DECLIC can be carried out in 2 different ways:
•Either while integrating the motor in the hood or in the kitchen furniture.
•Either while separating the motor, to be placed at a distance from the hood, in order to be more comfort-
able improving noise level
Extractor DECLIC + extern motor at a distance MISTRAL 800
The telescopic extractor DECLIC is installed in the hood or in the kitchen furniture;
the MISTRAL motor is tted at a distance from the hood on an outside wall.
A -INSTALLATION WITH THE CONFORT PRO MOTOR FIXED INTO THE BUILT-IN TELESCOPIC
EXTRACTOR
1.Turn the screws anticlockwise to loosen the 2 xing clips on the Declic (g 1).
2.Position the Confort motor inlet above the Declic and lower into position (g 2).
3.Fix the Declic motor assembly to the Confort with the 2 screws (g 3).
4.Insert the 4 shock absorbers into the holes in the back of the Confort motor (g 4).
5.The Declic is supplied with a 10mm and 20mm spacer to ll the gap between the wall and the rearof
the extractor. To t the spacer unscrew the screws located between the halogen lights and removethe
front light housing in order to access (g.5).
6.Cut the require aperture in the base of the kitchen cabinet as indicated (g. 6).
7.Insert the telescopic extractor in the aperture in the kitchen cabinet and turning the screws clockwis-
esecure the assembly to the kitchen cabinet (g 1).
8.We recommend that the CONFORT PRO motor be secured to the back of the kitchen cabinet,which
will allow access via the cabinet door (g 7).
9.Insert the grommets into the screw holes (g 8).
10.Connect the ducting onto the round outlet on the top of the motor assembly.
11.Connect both appliances together (g 9) and connect them to the mains supply
(See ELECTRICALWIRING chapter).
CAUTION : If the kitchen cabinet does not have a door you must execute points 10 and 11 be-
forepoint 7.
•RECIRCULATION
In the recirculation mode (with the optional activated charcoal lter tted) the contaminated air enters
thehood through the grease lter and through the purifying activated charcoal lters and back out into
thekitchen through a grille in the front of the kitchen cabinet (g. 10).Before the charcoal lter can
be tted it is necessary to x the propeller shaped bracket over the outlet inthe body of the canopy
using the 3 No M4 x 6 screws provided and then the activated charcoal cartridgecan be tted (g 11).
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Roblin Declic 609 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Roblin Declic 609 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 2,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info