490285

Roblin Cube 900 Manual

10
Zoom out
Zoom in
Previous page
1/60
Next page
8
GB
markings identifying the terminals in your plug, proceed as follows.
- The wire which is coloured green and yellow must be connected to the terminal in the plug which is
marked with the letter E or by the earth symbol or coloured green or green and yellow.
- The wire which is coloured blue must be connected to the terminal which is marked with the letter N
or coloured black.
- The wire which is coloured brown must be connected to the terminal which is marked with the letter
L or coloured red.
ATTENTION: Do not forget to use adequate plugs to the support brackets. Enquire after the manu-
facturers. Do an embedding if necessary. The manufacturer accepts no responsibility in case of a
faulty hanging due to the drilling and the setting up of plugs in the ceiling.
1) Unpack the hood parcel.
• LAYING OUT BEFORE FITTING THE HOOD
2) Mark the centre of the cooking appliance onto the ceiling with a plumb line. Draw the horizontal axes
running parallel to the stove top onto the ceiling as illustrated Fig. 1.
3) Place the drill gauge centred on the axes aligning the axes on the drill gauge centrally over these
axes as illustrated Fig. 1.
Mark the positions on the ceiling for : - The cut-out for the ducting Ø 150 mm in the extraction
mode and Ø 200 mm in the remote mode when ducting runs through the ceiling.
- The mains supply cords.
- The 8 xing holes for Ø 10 mm nuts and bolts.
Drill the different holes with the appropriate masonry bit. When xing the cooker hood to a plasterboard
ceiling ensure it is reinforced as illustrated in Fig. 2 and attach using four Ø10mm nuts and bolts; ensuring
the bolts as sleeved between the plasterboard and the joist supports to prevent the ceiling being damaged
when the bolts are tightened up.
If the ceiling is concrete, use eight Ø 10 mm steel rawl bolts. Plastic rawl plugs must not be used.
4) Draw a vertical line onto the wall from the centre of the cooking appliance up to the ceilling, using a
spirit level and a marker pen as illustrated in Fig. 1 - item 1. This is to ensure the correct alignment
of the chimney hood.
5) Drilling xing holes 2 (Fig. 1 ):
Mark a point on the vertical line at a distance from the cooking appliances of:
d = 650 + 51 = 701 mm (Measurement without splashback).
The distance H is the minimum height in mm from the cooking appliances to the bottom edge item 3 of
the front panel of the hood.
At the point marked, draw a horizontal line parallel to the cooking appliances. Drill 4 holes 2 in the wall
using an 8 mm drill bit and insert the rawl plugs into the holes. Fix the brackets item 2, using the 4.2
x 44.4 mm screws 12a and rawl plugs supplied. Small adjustments can be made using the hood
adjustment screws (see Fitting the canopy Fig. 10.1 & 2).
6) Aligning its centre on the vertical line, mark the 4 eyelet holes of the upper canopy bracket onto the
wall about 448 mm from the ceiling or from the upper limit. Drill the holes for the xing bracket using
an 8 mm masonry bit.
7) Fixing the canopy: Before starting to x the canopy it will be necessary to follow the instructions Fig.
3 to 9.
The height of the cooker hood can be adjusted in 53 mm stages. 650 mm when tting above an electric
hotplate and 700 mm when tting above a gas hotplate. Select the height required using the measure-
ments illustrated in Fig. 9 and x the metal diffuser to the frame of the chimney brackets using the height
5 x 10T hexagonal headed screws. A drawing on the drill gauge denes the positioning for the controls.
8) Place the canopy onto the wall brackets and x it to the ceiling as illustrated in Fig. 10.1.
Attention: 2 persons are necessary to secure this operation.
And then follow the instructions Fig. 10.1 & 2.
9) Check the vertical of the chimney.
10) Ducting:
The hood is more effective when used in the extraction mode (ducted to the outside). When the cooker
hood is ducted to the outside, charcoal lters are not required.The ducting used must be 150 mm (6
INS), rigid circular pipe and must be manufactured from re retardant material, produced to BS.476
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Roblin Cube 900 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Roblin Cube 900 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 2,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info