625588

Robland RAV 38 Manual

12
Zoom out
Zoom in
Previous page
1/15
Next page
afapmx-E.N.F9304.doc
ROLLER
REPLACEMENT
(FIG. 20)
WARNING: Disconnect
feeder from power source.
Remove SCREWS and replace
ROLLER(s). Replace SCREWS
with each roller replacement.
NOTE:
“ROTATE” roller positions
periodically will prolong the usage
of rollers.
ROLLER TIRE
REPLACEMENT
(FIG. 21, 22 & 23)
(Heavy-duty models,
3 or 4 Rollers)
1. Remove 4 SCREWS. (FIG. 21)
2. Force ROLLER-WHEELS out.
POUND roller on tabletop.
(FIG. 22)
3. Pre-assemble FRIENDLY
ROLLER with new TIRE (FIG.
23), with MALE-WHEEL (marked
M) inside and FEMALE-WHEEL
(marked F) outside. Lined up
UNTHREADED HOLES of both
WHEELS.
4. Slip 2 x 40mm SCREWS all the
way through UNTHREADED
HOLES. (FIG. 23)
5. Tighten new ROLLERS to
housing.
6. Tighten 2 x 20mm SCREWS
through remaining holes.
7. Secure all SCREWS.
8. Disregard “SLIGHT
WOBBLING” of the new
TIRES. — It will adjust itself
once in use.
9. Check all SCREWS and
RE-TIGHTEN them after first run.
VERVANGING VAN DE
ROLLEN (FIG. 20)
OPGELET: Ontkoppel de
aanvoerder van het elektriciteitsnet.
Verwijder de schroef en vervang de
ROL(LEN). Vervang de schroef bij elke
vervanging van de rol
NOOT:
“UITWISSELEN” onderling van de rollen
(periodiek) verlengt de levensduur van de
rollen.
VERVANGING van de
BANDEN van de ROLLEN
(FIG. 21, 22 & 23)
(De zware modellen 3
of 4 Rollen)
1. Verwijder de 4 schroeven. (FIG. 21)
2. Verwijder het WIEL van de ROL.
KLOP de rol op de tafel.
(FIG. 22)
3. Hermonteer VOORZICHTIG de ROL met
de nieuwe BAND; (FIG. 23), met het
MANNETJES-WIEL (gemarkeerd met M)
aan de binnenkant en het
VROUWTJES-WIEL (gemarkeerd met F)
aan de buitenkant. Schik de BORINGEN
van de twee WIELEN..
4. Plaats 2 x 40mm schroeven volledig
door de BORINGEN. (FIG. 23)
5. Maak de rollen opnieuw vast.
6. Plaats 2 x 20mm schroeven door de
overblijvende boringen.
7. Maak alle schroeven grondig vast.
8. Negeer het „LICHT SLINGEREN” van de
nieuwe banden. — Dat komt vanzelf
goed bij het gebruik.
9. Controleer en draai alle schroeven
opnieuw vast na elk gebruik.
REMPLACEMENT DES
ROULEAUX (FIG. 20)
ATTENTION: Débranchez
l'alimentation.
Retirez les vis et remplacez le (s) rouleau
(x). Remplacez les vis après chaque
changement.
NOTE:
Faire une “Rotation" régulière
prolongera la durée des rouleaux.
REMPLACEMENT DES
PNEUS DES ROULEAUX
(FIG. 21, 22 & 23)
(Modèles lourds,
3 ou 4 Rouleaux)
1. Enlevez les 4 VIS. (FIG. 21)
2. Retirez le rouleau, pressez légèrement
le rouleau sur le dessus de la table.
(FIG. 22)
3. Pré-assemblez le rouleau avec le
nouveau pneu (FIG. 23), avec la roue
mâle (IDENTIFIE - M) à l'intérieur et la
roue femelle (IDENTIFIE - F) à
l'extérieur. Alignez les trous ( sans filets)
des deux roues.
4. Insérez 2 vis (40mm) à travers les
trous (sans filets) (FIG. 23)
5. Fixez les nouveaux rouleaux au
châssis.
6. Insérez 2 vis (20mm) à travers les
trous disponibles.
7. Serrez toutes les vis.
8. Ne vous préoccupez pas du léger
débalancement des nouveaux pneus,
l'ajustement se fera automatiquement
lors de l'utilisation.
9. Contrôlez et re-serrez toutes les VIS
aprés chaque utilisation
GB
N
F
M
F
FIG. 23
FIG. 21
FIG. 22
1
2
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robland RAV 38 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robland RAV 38 in the language / languages: English, Dutch, French as an attachment in your email.

The manual is 2,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info