625588
7
Zoom out
Zoom in
Previous page
1/15
Next page
afapmx-E.N.F9304.doc
Loosen LEVER (8) & adjust
CONTROL JOINT UPRIGHT
90° to HOUSING. Tighten
LEVER (8). (SEE 6-3).
F) Assemble FEEDER to OVER
ARM (2). Tighten SCREWS (9).
MAKE SURE:
Center of LEVER (10) is IN
LINE with center of
OVER-ARM (2). (SEE 6-4).
G) Move FEEDER to desired
position by loosen LEVER (10).
Adjust height (11 & 12) and
extension (4 & 5) accordingly.
H) Tighten all LEVERS.
IMPORTANT:
There is certain PLAY between
ELEVATING KEY & BRACKET
GROOVE. To assure STURDY
FEEDING, pull FEEDER against
your IN-FEED direction, then
tighten LEVER (12). (SEE FIG. 8)
Do it on EVERY ADJUSTMENT.
Maak HEFBOOM (8) los & pas het
CONTROLEPUNT aan 90°
LOODRECHT op de BASIS. Maak
HEFBOOM (8) vast. (ZIE 6-3).
F) Monteer de aanvoerder op de ARM (2).
Maak schroef (9) vast. WEES ER
ZEKER VAN:
CENTER VAN DE HEFBOOM (10) is IN
LIJN met het center van de ARM (2).
(ZIE 6-4).
G) Verplaats de aanvoerder op de vereiste
positie door de HEFBOOM los te maken
(10). Pas de hoogte (11 & 12) en de
verlenging (4 & 5) gepast aan.
H) Maak alle HEFBOMEN vast.
BELANGRIJK:
Er is een zekere marge tussen verheffende
SLEUTEL & de gleuf van de HAAK. Te
verzekeren ―ROBUUSTE AANDRIJVING
(Niet met stoten), Trek de aanvoerder tegen
uw INGANGS-richting, daarna maakt u de
HEFBOOM (12) vast. (ZIE FIG. 8) Doe het
bij ―ELKE AANPASSING.
Desserrez la poignée (8), ajustez la
bride de moteur
perpendiculairement au châssis,
serrez la poignée (8) (Voir FIG. 6-3).
F) Fixez l'alimentateur au bras ajustable
(2) serrez les vis (9) ASSUREZ-VOUS
DE:
D'aligner le centre du bras ajustable
(2) avec le centre de la poignée (10)
(Voir FIG. 6-4).
G) Positionnez l'alimentateur à la position
désirée en desserrant la poignée (10).
Ajustez la hauteur (11 et 12) et le
déplacement latéral ( 4 et 5 ) selon la
position choisie.
H) Serrez toutes les poignées.
IMPORTANT:
Il y a un jeu entre la clé d'élévation et la
vis d'élévation. Pour assurer une
alimentation ferme, tirez l'alimentateur
vers la direction d'alimentation puis serrez
la poignée (12). (FIG. 8) Le faire après
chaque ajustement.
OPERATION
CONTROLS
(FIG. 9 & 10)
WARNING: Disconnect
feeder from power source.
OPERATIE-CONTROLE
(FIG. 9 & 10)
OPGELET: Koppel de aanvoerder
af van het elektriciteitsnet.
MANŒUVRES DE
FONCTIONNEMENT
(FIG. 9 & 10)
ATTENTION: Débranchez
l‟alimentation électrique.
GB
F
N
FIG. 9
13
12
11
5
4
2
10
FIG. 10
9
8
16
15
7
14
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robland RAV 38 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robland RAV 38 in the language / languages: English, Dutch, French as an attachment in your email.

The manual is 2,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info