625561
32
Zoom out
Zoom in
Previous page
1/46
Next page
NX SERIES V0913 31
English
Spindle
Mounting the tools on the spindle (fig.18)
1 Set the brake release switch of the selector switch on in order to free the brake and turn the
spindle free by hand and set the Allen key on the countersunk Allen bolt on top of the spindle
arbor (1)
2 Push the locking lever (2) to the right and, at the same time, manually turn the spindle arbor (3)
until the lower locking pin locks into the hole in the spindle.
3 Now loosen the clamp screw on top of the arbor with the Allen Key.
4 Always mount the spindle as low as possible on the arbor, so the bearing isn’t overloaded.
5 Mount the correct number of spindle rings and tighten the screw, on top of the arbor.
6 When the lever (2) is released, the locking of the spindle arbour is automatically disengaged.
7 Always lock the position of the spindle height by locking the handle (3) behind the handwheel.
Fig.18
Adjusting the spindle height (g. 18)
1 Unlock the locking lever (3) by turning it to the left.
2 The spindle arbour can be raised or lowered using the hand wheel (4).
3 After height adjustment always secure the spindle arbour by locking the lever (3) by turning it to
the right.
Remark: When, after intensive use of the locking lever (3), it is no longer possible to lock this lever, take
off the nut and remove the lever. Then turn it 1/6 turn to the right before putting it back on again. Put the
nut back on and tighten it.
The spindle fence
Working with the spindle fence (fig. 19)
The spindle fence is tted onto the table with two locking knobs (1). The body of the spindle fence is
equipped with two slots which enables front and back movement. When the fence is tted onto the table,
the position of the aluminium fence plates can be adjusted by means of the adjustment knob (2). The
opening of the 2 fence plates goes like follows: loosen the wing nut (3) which hold the fence and move
the fence towards each other, so there is a minimal gap between the protruding tool and the fence plates.
It is advisable to use a false fence or integrated fence which is mounted between the 2 spindle fences.
The adjustment of the fences can be checked with a at and precise rule.
Before starting the machine, the blocking of the bars of the fences on the table has to be checked. The
wood pushers exert vertical and horizontal pressure on the work piece, which pushes the work piece
against the table and the fence and which makes it slide easily. The manual wood pusher (g. 20),
supplied with the machine, can be used to push the wood safely. Not one element is xed on the useful
table surface. The 10 mm space between the base of the horizontal wood pusher and the table makes it
possible to move the wood pusher under the wood pushers. To replace the spindle tool, or to make use
of the feeder, the whole pusher system can be cleared by ipping it over to the back of the spindle fence:
Pull the lever in the direction of the arrow. Lift up a little the cover plate. Now the system can be ipped
over to the back. This part will prevent the fences from falling down. It is advisable to use a Q1
1
2
3
4
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robland NXSD 310 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robland NXSD 310 in the language / languages: English as an attachment in your email.

The manual is 1,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robland NXSD 310

Robland NXSD 310 User Manual - German - 100 pages

Robland NXSD 310 User Manual - Dutch - 100 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info