625545
34
Zoom out
Zoom in
Previous page
1/98
Next page
HX SERIES V0212 33
English Deutsch
Warning: the mortiser chuck has a left hand thread!
Put the chuck onto the spindle arbor up to the end and check if the V-groove (2) in the spindle matches
with the 2 holes in the chuck (if not, the spindle thread will be damaged!). Introduce the 2 Allen screws
(1) and tighten them well. These press screws are needed to prevent the chuck from loosening.
Maintenance (g. 35, 36, 37)
Warning: always disconnect the machine from its power supply before starting any maintenance
work!!!!
The interior and exterior parts of the machine must be cleared at regular intervals to avoid
accumulation of dust and woodchips. Any deposits of resin on the cross cut table sliding bars or on
any other moving part of the machine must be removed with a piece of cloth and a little solvent (petrol,
kerosene or other product). Never smoke or have any naked ame near the machine when using
inammable products, this to prevent risk of re and serious burns for the operator.
All bearings are double sealed and lubricated for life, therefore they need no maintenance. All columns,
e.g. spindle, thicknesser, mortiser need to be lubricated once a month, especially when the machine
is used in a very humid environment. The best product to use is simple penetrating oil in a spray can.
All other moving parts have to be kept free of dust and woodchips and may be greased with the same
penetrating oil.
The use of a dust extraction system will most certainly extend the life of your machine. The life of the
motors can be extended by blowing out saw dust from the cooling fan and from the motor body itself.
Remove the plate (g. 35) by lifting it up and taking it out. The drive belts for the planer motor can easily
be tightened by loosening the 4 nuts (1) holding the motor to the frame.
The motor, under its own weight will lower and tighten the belts.
Fig.35
The saw belts tension (g. 36) can be adjusted by tilting the saw blade to 45°; then the spanner bolt
(1) can be seen and reached just above the rise and the fall handle for the saw. By turning this bolt
clockwise the saw belt will be tensioned, anti-clockwise loosened.
1
34


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robland HX260 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robland HX260 in the language / languages: English, German as an attachment in your email.

The manual is 5,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robland HX260

Robland HX260 User Manual - Dutch, French - 102 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info