625545
8
Zoom out
Zoom in
Previous page
1/98
Next page
HX SERIES V0212 7
English Deutsch
Normal use and
prohibited use
CIRCULAR SAW
The table saw assembly is designed for the following working processes and equipped with protective
devices. It is not designed to work materials such as ferrous or non-ferrous materials, and therefore
tasks that differ from the ones stated below are prohibited.
Ripping with the parallel saw fence with/without tilted saw blade with the fence upright or in the low
position.
Right-angled or mitre cuts with the 90° fence mounted to the sliding table with tilted or vertical saw
blade.
Cross cutting work pieces with the adjustable stop on the 90° fence.
Cutting panels or solid wood on the sliding table.
PROHIBITED USE
Following tasks are prohibited on the table saw:
submerged cuts by removing the riving knife and/or guard;
all types of cuts without using the table saw fence, the 90° fence or sliding table;
cutting large work pieces that exceed the table capacity without using aids such as roll supports.
REMAINING RISKS
Main risks on a table saw are:
unintentional contact of the hands with the running saw blade;
work piece kickback;
tipping of the work piece due to insufficient support.
MOULDER-SHAPER
The sharper assembly is designed for the following tasks and equipped with protective devices. Other
tasks than listed below are therefore prohibited.
mould and form straight and curved pieces on the vertical spindle;
shaping of curved work pieces using a ring guard fence;
mortising, tenoning and panel edge shaping using corresponding safety devices.
PROHIBITED USE
The following tasks are prohibited on the moulder-shaper unit:
down-cut shaping, i.e. when feed and tool rotation direction is the same;
slotting with saw blades;
using tool diameters which are not adapted to the spindle by using reducing sleeves;
using larger tool diameters and higher speeds than the shown in the diameter-speed diagram;
the use of ferrous and non-ferrous materials.
REMAINING RISKS
Spindle shapers are one the main causes of injuries in woodworking. Nearly all accidents result in
hand injuries. They are due to contact with the rotating tool when the work piece is fed by hand and
kickback occurs to sudden forward movement of the work piece.
The main danger areas on the shaper-moulder are:
the working area;
the moving machine and tool parts;
the kickback area.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robland HX260 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robland HX260 in the language / languages: English, German as an attachment in your email.

The manual is 5,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robland HX260

Robland HX260 User Manual - Dutch, French - 102 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info