467089

Robbe Futaba T8FG Manual

26
Zoom out
Zoom in
Previous page
1/123
Next page
26
<Basic Operation>
Easy Link (T8FG/R6008HS)
Each transmitter has an individually assigned, unique ID code. In order to start operation, the receiver
must be linked with the ID code of the transmitter with which it is being paired. Once the link is made,
the ID code is stored in the receiver and no further linking is necessary unless the receiver is to be used
with another transmitter. When you purchase additional R6008HS receivers, this procedure is necessary;
otherwise the receiver will not work.
Link procedure
1. Place the transmitter and the receiver close
to each other within one (1) meter.
2. Turn on the transmitter.
3. Check the LED that is placed on the front
side of the transmitter to see if the RF signal is
active. When the right LED is ON solid, the RF
signal is being sent.
4. Turn on the receiver.
LED
Link/Mode Button
5. Press down the Link/Mode button for more
than two seconds, and release the switch.
The receiver begins the linking operation.
6. When the linking is complete, the LED in the
receiver will change to solid green. Please
conrmthat the servosarenowoperational
from your transmitter. Please refer to the
table b e l o w fo r the LED status of t h e
receiver's condition.
* If there are many FASST systems turned on around your
receiver, it might not link to your transmitter. In this case,
even if the receiver's LED stays solid green, unfortunately
the receiver might have established a link to one of other
transmitters. This is very dangerous if you do not notice
this situation. In order to avoid the problem, we strongly
recommend you to doublecheck whether your receiver is
really under control by your transmitter by giving the stick
input and then checking the servo response.
LED Indication (R6008HS)
Green Red Status
Off Solid No signal reception
Solid Off Receiving signals
Blink Off
Receiving signals but ID is
unmatched
R6008HS Easy Link
TM
Operation
0 to 2 sec. More than 2 sec.
0 sec. 2 sec.
Press and Hold time
No function(Function)
Re-link(ID set)
󾙏
Warning
󾙋
After the linking is done, please cycle receiver
power and check if the receiver to be linked is
really under the control by the transmitter to be
linked.
󾙍
Do not perform the linking procedure with
motor's main wire connected or with the engine
operating as it may result in serious injury.
… 26 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robbe Futaba T8FG at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robbe Futaba T8FG in the language / languages: English as an attachment in your email.

The manual is 10,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robbe Futaba T8FG

Robbe Futaba T8FG User Manual - German - 72 pages

Robbe Futaba T8FG User Manual - Dutch - 123 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info