747912

Robbe Futaba T6EX Manual

25
Zoom out
Zoom in
Previous page
1/38
Next page
25
3. Use SELECT key to select the desired curve point. Point 1 is shown initially which is throttle
stick’s all the way downward (slow) position. Point 5 is throttle stick’s all the way upward (hi)
position.
4. Push up or down DATA INPUT lever to set the servo position.
5. Use SELECT key to set other points in same manner.
I-PI Idle-up pitch curve function: (HELI only)
Used to set pitch curve for idle up flight. 5-point pitch curve is utilized to best match the blade collective pitch to the consistent
engine RPM when idle up is used. Pitch curve can be adjust from 0-100% each point.
The high side pitch curve should be set to not overload the engine and keep consistent engine RPM. Generally, set less pitch
than normal maximum pitch. The low side pitch curve should be set for desired maneuvers such as loops, rolls, and 3D flight.
To set the idle-up pitch curve:
1. Enter the programming mode and use the MODE key to access the “I-PI” function.
2. This is the idle up pitch curve, to use this function the
“I-TH” Idleup throttle function must be
activated first.
3. Use SELECT key to select the desire curve point. Point 1 is shown initially, which is the
throttle stick’s all the way downward (slow) position. Point 5 is the throttle stick’s all the way
upward (hi) position.
4. Push up or down DATA INPUT lever to set the servo position.
5. Use SELECT key to set other points in same manner.
HOLD Throttle hold function (HELI only)
Throttle hold function is to be used for autorotations where only pitch control is used to make
a descent and landing. Just flip the hold switch on to set the engine in the idling or cut position
and disengage it from the Throttle Stick. It can be set from (-)50 to (+)50% from throttle trim
position.
To set the throttle hold:
1. Enter the programming mode and use the MODE key to access the “HOLD” function.
2. Push the DATA INPUT lever upward for 0.5 seconds. This will cause the flashing “INH”
display to change to a flashing “OFF” or “ON” display. Now the “HOLD” function is on.
(“OFF”: if the throttle hold switch is off, “ON”: if the throttle hold switch is on.)
3. Push SELECT key once. This will cause the flashing “%” symbol on the display. Pull the hold
switch towards you. Push up or down DATA INPUT lever to set the throttle servo position of
throttle hold.
… 25 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robbe Futaba T6EX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robbe Futaba T6EX in the language / languages: English as an attachment in your email.

The manual is 2,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info