747912
6
Zoom out
Zoom in
Previous page
1/38
Next page
6
Trim levers (all) - Used to shift the neutral or center position of each servo as labeled in the diagram. Once either trim lever
is operated, the trim position is displayed on the LCD screen. Also once either edit key is operated, all trim positions are
displayed sequentially on the LCD screen.
NOTE: The throttle trim lever is intended for fine tuning the throttle servo when the engine is at idle. Throttle trim does not
affect the throttle servo when the throttle control stick is all the way up (so idle r.p.m. can be adjusted without affecting
throttle settings through the rest of the stick movement).
Charging jack - Port for charging the transmitter batteries with the included battery charger.
On/off switch
DATA INPUT lever - Used to change the values of the various functions displayed on the LCD screen
Liquid – crystal display screen (LCD) - Displays programming modes and values entered.
MODE key - Used to scroll through and display the “11-14” different functions.
SELECT key - Used to display the values for the current function.
Throttle – cut button - To use the throttle-cut function, lower the throttle stick all the way, then push the throttle-cut button to
fully close the carburetor and shut off the engine.
Throttle/rudder control stick - Operates the servos connected to channel 3 (throttle) and channel 4 (rudder) in the receiver.
A:Trainer switch - Operates the trainer functions. To operate as a trainer switch the transmitter must be connected to another
transmitter via. a trainer cord (available separately).
H:Idle – up switch - This switch operates to change the fight condition which sets the throttle curve and pitch curve of mid
air maneuvers (rolls, loops, stall turns) and 3D flight.
A:Retractable landing gear switch/Channel 5 - Switch operates the servo connected to channel 5 in the receiver. If your
model has retractable landing gear, this is the control used to extend and retract the gear.
H:Gyro switch/Channel 5 - You can connect the sense adjust connector to channel 5 of the receiver to operate the gyro,
which has two different senses. Also if you use the Futaba GY401/502/611 Gyro, two different gyro sense settings on the gyro
function in this transmitter can be called by this switch.
Antenna - Radiates signals to the receiver. NEVER point at the model when flying! See page 9 for detail.
Changing the Throttle Stick Ratchet System to Helicopter-touch
1. Open the battery cover on the back of the transmitter and remove the transmitter battery.
2. Remove the four transmitter rear case screws and remove the rear case.
3. Change the ratchet plate on the gimbal section to the smooth ratchet plate for helicopter use.
Ratchet plate
for airplane
Ratchet plate
for helicopter
(The above photos show a Mode 2 system as supplied. )
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robbe Futaba T6EX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robbe Futaba T6EX in the language / languages: English as an attachment in your email.

The manual is 2,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info