467096
19
Zoom out
Zoom in
Previous page
1/128
Next page
19
<Before Use>
Connector/Plug
Ɣ'6&7UDLQHUƔ%DWWHU\FKDUJH
Connector for trainer function
When you use trainer function, connect the
optional trainer cable between the transmitters for
teacher and student.
*You can set the trainer function on the Trainer Function
screen in the system menu.
Connector for DSC function
You can operate the transmitter without
transmitting radio waves by connecting the
transmitter and the receiver to the DSC cable.
*Please refer to the section "Connection between Receiver/
Servo"
Connector for battery charger
This is the connector for charging the Ni-
MH battery HT6F1700B that is installed in the
transmitter. Do not use any other chargers except
the attached special charger corresponding to Ni-
MH battery.
Danger
Do not connect any other chargers except the
special charger to this charging connector.
*If you take out the Ni-MH battery HT6F1700B from
the transmitter, you can use the optional quick charger
CR-2000 corresponding to Ni-MH battery.
Installing and Removing of the battery
HT6F1700B for the transmitter
Attachment of the battery
1. Open the battery cover on the rear of the
transmitter toward upper side.
ƔBattery ribbon for
removing battery
2. Install the battery in the holder.
ƔBattery ribbon
*Push the battery
until being locked
completely.
ƔConnector
3. Connect the battery connector.
4. Close and lock the battery cover completely.
Removing of the battery
Note: If you remove the battery while the
power is on, the data you have set will not
be saved.
1. Open the battery cover on the rear of the
transmitter toward upper side.
2. Disconnect the battery connector.
3. Pull up the battery ribbon to release the lock.
4. Remove the battery.
5. Close and lock the battery cover completely.
Warning
Be careful to not drop the battery.
Never disconnect the battery connector
from the T12FG transmitter while
some message are displayed on the
screen after turning off the power the
T12FG transmitter.
* Internal devices such as memories may be damaged.
* If there is any problem, the message "Backup Error" will
be shown the next time when you turn on the power of the
transmitter. Do not use the transmitter as it is, send it to the
Futaba Service Center.
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robbe Futaba T-12 FG at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robbe Futaba T-12 FG in the language / languages: English as an attachment in your email.

The manual is 1,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robbe Futaba T-12 FG

Robbe Futaba T-12 FG User Manual - German - 78 pages

Robbe Futaba T-12 FG User Manual - Dutch - 80 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info