520094
7
Zoom out
Zoom in
Previous page
1/105
Next page
Transmitter controls
FX-40
7
In the Linkage menu “Dial Monitor” the current and stored
positions of the rotary knobs are displayed in bar graph form.
The centre rotary knob CD is a digital control with no end-
stops, and it also features an integral push-button function
(CD-SW). This control can also be assigned freely to any func-
tion. The transmitter emits an audible signal when the knob is
moved to the centre position. The position of this control is
also displayed on the Start screen.
LINEAR SLIDERS
The centre of the transmitter houses three linear sliders with a
centr
e detent. These analogue contr
ols can also be assigned
freely to any function you wish. The transmitter emits an audi-
ble signal when the slider is moved to the centre position.
In the Linkage menu “Dial Monitor” the current and stored
positions of the linear sliders are displayed in bar graph form.
DIGITAL TRIMMERS
The transmitter features two digital trimmer buttons (T5 + T6).
Every time a button is moved, the trimmer value alters by the
selected incr
ement. If a trimmer button is held at one end-
point in or
der to adjust the trimmer value by a larger amount,
the rate of change automatically accelerates (auto-repeat
function).
If the trimmer position reaches the neutral point (centre posi-
tion), or passes the neutral point, the transmitter emits an
audible signal. The current trim position is displayed as a bar
graph in the Start display and also in the “Dial Monitor” menu.
The trimmer buttons can be assigned freely to any functions,
and can also be used as transmitter controls for mixer func-
tions.
The trimmer rate and increment can be selected individually
for each trim button in the “Function” menu.
• You can fit the switches in any position you like.
The default position of the switches is as follows:
In each case the centre wir
e of the cable is colour-coded, and
is assigned permanently to the following switches:
Please ensure that the wire
colours are correctly connec-
ted after you have r
e-positio-
ned the switches, otherwise
the graphical on-scr
een
assignment will be displayed
incorrectly.
After re-positioning the switches, fit the crown nuts again
and tighten them using the special spanner supplied.
Fit the back panel and tighten the retaining screws.
After the re-positioning exercise you should now call up the
System menu “Switch” (page 35) and alter the switch types
and position numbers, so that the graphical switch position di
play reflects the new configuration and is displayed correctly on
the screen.
CENTRAL ROTARY KNOBS
The rotary knobs LD and RD are analogue contr
ols which can
be assigned freely to any function. They feature a fine centre
detent, and the transmitter emits an audible signal when they
are moved to the centre position. If you wish, they can be
retracted by pushing the knob in using light pressure.
Switch Position Typ Lever
SA 3-position Change-over Short
SB 3-position Change-over Short
SC 3-position Change-over Long
SD 3-position Change-over Short
SE 3-position Change-over Short
SF 2-position Change-over Long
SG 3-position Change-over Short
SH 3-position Change-over Short
SWITCH Cable colour
SA and SC green
SB and SD yellow
SE and SG orange
SF and SH brown
L1
L2
L3
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robbe Futaba FX-40 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robbe Futaba FX-40 in the language / languages: English as an attachment in your email.

The manual is 3,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robbe Futaba FX-40

Robbe Futaba FX-40 User Manual - German - 105 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info