467093
70
Zoom out
Zoom in
Previous page
1/103
Next page
AILE-FLAP (GLID2FLP only): This pre-programmed mix is used to create full span aileron action on a glider with 4
wing servos. This increases the roll rate and decreases induced drag. For normal flying, a value of about 50% is
often used. For slope racing or F3B models in speed runs, you may wish to use a larger value approaching 100%.
Adjustability:
RATE range of -100 to +100. Negative setting would result in opposite aileron action from flaps.
SWITCH A-H fully assignable.
POSITION fully assignable, including NULL (mix always on) and Up&Cntr and Cntr&Dn to activate the mix in 2
separate positions of the same S
WITCH. (This allows easy setup of one SWITCH position which is no FLAP-AILE
or AILE-FLAP mixing, one with both FLAP-AILE and AILE-FLAP mixing, and one with just FLAP-AILE mixing.)
GOAL of EXAMPLE: STEPS: INPUTS:
REAR VIEW OF MODEL WITH LEFT AILERON COMMAND
REAR VIEW OF MODEL WITH LEFT AILERON COMMAND
70
Turn on FLAP-AILE mixing. Set RATE to
48%, which is the portion of the total
aileron travel that matches the maximum
flap travel.
Ex: Set up S
WITCH C as follows:
UP = no full span mixing.
CTR = flap-ail and ail-flap
DWN = flap-ail mixing only.
Assign to S
WITCH C center and down.
Turn on AILE-FLAP mixing. Set rate to
100% for maximum possible flap
travel with ailerons.
Assign to SWITCH C center.
Where next?
Open FLAP-AILE mixing function.
Activate the function.
Set the rate. (Ex: 48%)
Optional: adjust the flap position at
which the flaperons are zeroed.
Assign the S
WITCH
and position.
(Ex: C Cntr&Dn)
Close the function.
Open AILE-FLAP submenu.
Activate the function.
Set the rate. (Ex: 100% each way)
Assign the S
WITCH
and position.
Close.
for 1 second.
(If BASIC menu , again.)
to 2nd page of menu.
to FLAP-AILE.
to ON.
to +48%.
or VR(A) as needed.
for 1 second to set.
to SW. to C.
to Cntr&Dn.
to AILE-FLAP.
to ON.
A
ILERON STICK
. to +100%.
AILERON STICK. to +100%.
to SW. to C.
to CENTER.
ELEV-FLAP mixing. See p. 54.
BUTTERFLY. See p. 55.
Use a mix to OFFSET the flaps a set distance on a specified switch: see p. 59.
View additional model setups on the internet: www.futaba-rc.com\faq\faq-9c.html
70


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robbe 9CHP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robbe 9CHP in the language / languages: English as an attachment in your email.

The manual is 4,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robbe 9CHP

Robbe 9CHP User Manual - Dutch - 83 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info