467094

Robbe 9CHF Manual

13
Zoom out
Zoom in
Previous page
1/103
Next page
13
PUSH
Ni-Cd battery pack
Charging jack
Battery cover
Battery connector location
Trainer function
/DSC function connector
RF module
To remove, press the tabs together
and gently pull rearwards.
To install, line up the connector pins with
the socket in the rear of the module and
gently snap into position.
Switch/Knob Airplane (ACRO) Sailplane/Glider (GLID) Helicopter (HELI)
A or H Tx.
SWITCH A elevator dual rate elevator dual rate elevator dual rate
down = butterfly on
Switch B rudder dual rate rudder dual rate rudder dual rate
Switch C up = ELE-FLP on up = ELE-FLP on governor/ch 7
center/down = IDLE-DOWN center/down = IDLE-DOWN
down = AIRBRAKE on
S
WITCH D aileron dual rate aileron dual rate aileron dual rate
Switch E
OR G* landing gear/ch 5 GLID1FLP = gear throttle hold
Switch F
OF H* snap roll/trainer trainer trainer/THR-CUT
SWITCH G OR E* none back = SPEED OFFSET idle-up 1 and 2
fwd = START OFFSET
SWITCH H OR F* none none idle-up3/ch 5/gyro
K
NOB A flap/ch 6 GLID1FLP: flap HOVERING PITCH
(flap trim if FLAPERON on) (flap trim if FLAPERON on)
GLID2FLP: camber
(flap trim if FL-AIL off)
K
NOB B ch 8 ch 8 ch 8
K
NOB C spoiler/ch 7 spoiler/ch 7 HOVERING THROTTLE
(disabled if AIL-DIFF on) (disabled if AIL-DIF on)
S
LIDER D none GLID1FLP: ch 5 none
S
LIDER E none none none
*On the 9CH transmitters, the TOP LEFT SWITCHES are spring-loaded and 3-position; on the 9CA, those switches are on the right side. For consistency,
the switch position’s designation remains the same (upper left is F, etc), but the functions are moved to match the switch type.
NOTE: If you need to remove or replace the transmitter battery, do not pull on its wires to remove it. Instead,
gently pull on the connector's plastic housing where it plugs into the transmitter.
SWITCH ASSIGNMENT TABLE
•
The factory default functions activated by the switches and knobs for a Mode 2 transmitter are shown below.
•
Most 9C functions may be reassigned to non-default positions quickly and easily.
•
Basic control assignments of channels 5-9 are quickly adjustable in AUX-CH (see pp. 39). For example, the channel 5
servo, which defaults to SWITCH E for retract use, can easily be unassigned (NULL) to allow for easy use as a second
rudder servo in a mix, or to a slider or dial for bomb door or other control.
•
Note that most functions need to be activated in the programming to operate.
•
Mode 1 transmitter functions are similar but reverse certain switch commands. Always check that you have the desired
switch assignment for each function during set up.
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robbe 9CHF at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robbe 9CHF in the language / languages: English as an attachment in your email.

The manual is 4,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robbe 9CHF

Robbe 9CHF User Manual - Dutch - 83 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info