471681
4
Zoom out
Zoom in
Previous page
1/32
Next page
EnglishEnglish
34
POWER SUPPLY
This unit operates from a main supply of 230V ~ 50Hz. Connect the AC power cord to the AC
household main outlet. Ensure that the voltage is as indicated on the rating plate on the rear
of the unit.
Battery Back-up Power Failure Protection
This radio has a battery back up circuit that will keep the correct time and alarm settings in
the event of a temporary power interruption.
Install 1 x 3-volt CR2032 Flat Lithium battery, not included, into the battery compartment
located on the bottom of the unit, making certain that the positive and negative (+ and -) battery
terminals are attached to the corresponding terminals on the plate in the battery compartment.
If power is temporarily interrupted the display will blink and the radio will not play. However,
the battery back-up circuit will continue to maintain the clock and alarm settings. When power
is restored the clock will display the correct time and alarm settings, and no adjustment is
necessary.
GETTING STARTED
Press the Reset button (17) located on the back of the unit after pluging in the AC cord.
- The unit will display full segment for 2 seconds, then it will enter the normal mode.
- The Display will light up.
1. TIME AND CALENDAR SETTING
A. Setting Time and Calendar - Press Mode Set button (1) in normal mode and keep pressed
over 2 seconds to enter Time Set mode. After entering the setting mode, press Mode Set
button (1) to change the mode cycle as follows :
Normal > Year > Month > Day > 12/24H > RTC Hour > RTC Min > Normal
Action (during data adjustment) :
- Press >> button (7) to adjust data forward
- Press << button (8) to adjust data backward
- Keep pressed << or >> button for 2 seconds to enable auto forward or backward
a. Year Set Mode
Initial Value : 2009
Year Range : 2000 to 2099
Display showing Year Set Mode
b. Month Set Mode
Display showing Month Set Mode
c. Day Set Mode
Display showing Day Set Mode
Remark : Weekday will recalculate when year, month or day is adjusted
d. 12/24H Set Mode
Display showing 12/24H Set Mode (Select 12H)
Display showing 12/24H Set Mode (Select 24H)
e. RTC Hour Set Mode
Display showing Hour Set Mode
f. RTC Min Set Mode
Display showing Min Set Mode
Remark : Second will reset for every minute adjustment
M
D
M
D
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Roadstar CLR-2619 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Roadstar CLR-2619 in the language / languages: English, German, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info