559867
9
Zoom out
Zoom in
Previous page
1/12
Next page
CONOZCA SU FABRICADOR DE HELADO
A. MOTOR (DISEÑO CONO DE NIEVE)
Montado en la parte superior. Engrana
la PALETA y cierra hasta el cubo
enfriador.
B. CUBIERTA
La pestaña de la CUBIERTA encaja
sobre la ranura del ENVASE DE
HELADO.
C. PALETA
El extremo superior encaja dentro del
orificio del centro de la CUBIERTA y
engrana en el MOTOR.
D. ENVASE PARA HELADO
El recipiente contiene la mezcla de
helado.
E. CERRADURAS
Las CERRADURAS se usan para
asegurar el MOTOR al CUBO
ENFRIADOR (Ver diagrama que se
muestra en la parte inferior izquierda
de esta página en las instrucciones
para cerrar y liberar)
F. CUBO ENFRIADOR
Mantiene la sal de roca y el hielo.
COMO USAR SU FABRICADOR DE HELADO
NOTA: Antes de usarlo por primera vez, lave todas las partes excepto la
UNIDAD DE MOTOR (vea “COMO LIMPIAR SU FABRICADOR DE HELADO”).
1. Empiece con el ENVASE DE HELADO fuera del CUBO ENFRIADOR.
Vierta el helado pre-mezclado de la receta o la mezcla dentro del
ENVASE DE HELADO. Llene el ENVASE DE HELADO solo hasta 3/4 de
capacidad, ya que la mezcla se va a expandir mientras se congela.
2. Inserte la PALETA, asegúrese que esté centrado dentro del ENVASE.
3. Coloque la CUBIERTA sobre el ENVASE DE HELADO, asegúrese que el
extremo superior de la PALETA entre dentro del orificio de la CUBIERTA.
4. Coloque el ENVASE DE HELADO cubierto en el CUBO ENFRIADOR.
5. Coloque el MOTOR sobre el ENVASE DE HELADO, asegúrese que
el extremo de la PALETA se inserte en el orificio debajo del MOTOR.
Asegúrese también de alinear los brazos de soporte del MOTOR sobre
las CERRADURAS del CUBO ENFRIADOR. Rote las CERRADURAS en
sentido de las agujas del reloj para trancar el MOTOR sobre el CUBO
ENFRIADOR.
6. Enchufe el cable eléctrico. El Motor automáticamente se prenderá y
ENVASE DE HELADO empezará a girar.
NOTA: La PALETA no rotará; solamente va a rotar el ENVASE DE HELADO.
7. Mientras el fabricador de helado está en marcha, distribuya 2 pulgadas
de hielo alrededor de la parte inferior del CUBO ENFRIADOR.
Luego espolvoree aproximadamente ¼ de taza de SAL DE ROCA
uniformemente sobre la capa de hielo. (Vea “Puntos Importantes” en
la próxima página). DEBE USARSE SAL DE ROCA. PARA MEJORES
RESULTADOS USE SAL DE ROCA RIVAL.
8. Continúe añadiendo capas de hielo y SAL DE ROCA hasta que el nivel
del hielo alcance el tope del ENVASE DE HELADO rotando.
9. El helado debe estar batiéndose aproximadamente entre 30-40
minutos o hasta que se obtenga la consistencia deseada. Nota: El
Motor no se va a detener automáticamente cuando el helado esté
listo. Para revisar la consistencia, desenchufe, libere el MOTOR y
retírelo junto con la CUBIERTA. Vuelva a colocar el MOTOR y la
CUBIERTA y enchufe para continuar batiendo.
NOTA: Si el fabricador de helado se detiene antes que se complete el
proceso (aproximadamente 30-40 minutos), hay que revisar si algunos
cubos grandes de hielo se quedaron atascados en el envase de
helado al rotar. (Vea “Puntos Importantes”)
A
D
C
B
E
E
F
Cierra
Libera
-S5--S4-
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rival FRRVBK02 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rival FRRVBK02 in the language / languages: English as an attachment in your email.

The manual is 0,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info