559874

Rival 8806 Manual

3
Zoom out
Zoom in
Previous page
1/8
Next page
• MOTOR DRIVE
Top mounted. Engages stem of
DASHER and locks to bucket.
• RUBBER CORK
Used to plug hole in COVER
when hardening ice cream.
• COVER
Tab in COVER fits notch in ice
cream can.
• DASHER
Stem on top fits through hole in
center of COVER, and engages
MOTOR DRIVE.
• ICE CREAM CAN
Container holds ice cream mixture.
• DRAIN HOLE
Allows salt water to flow freely out of BUCKET.
• BUCKET
MOTOR DRIVE tabs secure BUCKET. DRAIN HOLE located near top of
BUCKET. Holds rock salt and ice.
DASHER
4. Place filled ICE CREAM CAN in BUCKET. Make sure ICE CREAM CAN is
centered and engages with bottom of BUCKET.
5. Place MOTOR DRIVE over ICE CREAM CAN so that stem of DASHER
engages hole in bottom of MOTOR DRIVE. Rotate ICE CREAM CAN
slightly until MOTOR DRIVE engages ICE CREAM CAN COVER. Fit the
four tabs on the bottom of MOTOR DRIVE into holes at the top edge
of the bucket. Rotate the MOTOR DRIVE counter clockwise to secure to
bucket. Plug power cord into 120 volt AC outlet.
6. While ice cream maker is running, distribute 2 inches of ice around
bottom of BUCKET. Sprinkle approximately
1
/4 cup salt uniformly over
layer of ice. (See “Important points”) NOTE: The DASHER does not
move, the ICE CREAM CAN turns around it.
7. Continue adding layers of ice, with salt between layers, until ice level
reaches top of rotating ICE CREAM CAN. NOTE: Should ice cream
maker stop before churning is complete (approximately 20-40 minutes),
check to see if large ice cubes are jammed against the rotating ice
cream can. (See “Important Points”)
8. Ice cream should churn about 20-40 minutes or until motor stops.
Unplug and remove MOTOR DRIVE.
9. Clear ice and salt away from top of ICE CREAM CAN. Wipe carefully to
remove salt and water before removing the COVER. Lift out DASHER
and scrape clean with a rubber spatula. Pack ice cream down into ICE
CREAM CAN.
KNOW YOUR ICE CREAM MAKER
-4- -5-
HOW TO USE YOUR ICE CREAM MAKER
NOTE: Before using for the first time, wash all parts except MOTOR DRIVE
(see “HOW TO CLEAN YOUR ICE CREAM MAKER”).
1. Pour chilled ice cream mixture into cooled ICE CREAM CAN. Fill ICE
CREAM CAN only
3
/4 full, as mixture will expand during freezing.
2. Insert DASHER. Be sure that bottom of DASHER fits the indentation at
bottom of ICE CREAM CAN.
3. Place COVER on ICE CREAM CAN.
MOTOR DRIVE
COVER
RUBBER CORK
ICE CREAM CAN
BUCKET SLOTS
BUCKET
DRAIN HOLE
ROCK SALT for making ice cream
ROCK SALT for hardening ice cream
CRUSHED ICE for making and hardening ice cream
3 Cups
2 Cups
5-10 lbs.
4 Cups
3 Cups
10-15 lbs.
4 Quart 6 Quart
MAKER SIZE
For best results use Rival
®
Rock Salt
8804/8806/9100200000501 V.qxd 12/19/05 10:19 Page 5
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rival 8806 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rival 8806 in the language / languages: English as an attachment in your email.

The manual is 0,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info