713213

Ritter sono1 Manual

16
Zoom out
Zoom in
Previous page
1/86
Next page
11
Unfold the illustrations at the front
and back of this manual.
Please read these instructions
thoroughly before you start to use
the appliance. Keep these operat-
ing instructions in a safe place
and ensure that they are included
with the appliance if passing it on
to a third party.
Alternatively, the current operat-
ing instructions are available at
www.ritterwerk.de.
INTENDED USE
The food slicer is used for the slic-
ing of household foods.
The food slicer is suitable
for contact with
foodstus.
If the appliance is used for a
purpose other than this, or if it is
operated incorrectly, severe inju-
ries may occur or the appliance
may be damaged. All warranty
and liability claims will be ren-
dered null and void in this case.
BEFORE USING THE
APPLIANCE FOR THE
FIRST TIME
Preparation
Remove the appliance carefully
from the packaging. Remove all
packaging parts and keep these
together with the packaging in a
safe place. Clean the appli-
ance before allowing it to come
into contact with any food (see
CLEANING).
Setting-up the appliance
• Set the appliance down on a
at, nonskid surface close to a
mains socket.
Using a small amount of
force, push the slice carriage (9)
vertically into the guide groove on
the appliance until it audibly locks
into place.
Slide the left-over holder (10)
onto the slice carriage's handle.
compact
1
/ nova
1
/ no
1
Unwind the power cord (5) to the
length required from the cable
compartment (8) under the appli-
ance.
• Plug the cable into the socket.
SLICING
Use the slice thickness adjust-
ment knob (2) to set the required
thickness.
Note:
The slice thickness adjustment
scale is not a millimetre scale.
For safety reasons, the "0"
position is designed to cover the
blade.
Place the food to be sliced
onto the slice carriage (9). Use
the left-over holder (10) to press
it up against the stop plate (11).
Protect your hands, by always
using the slice carriage and,
where applicable, the left-over
holder. Exception: Excessively
large foods to be sliced.
Turn the appliance on using
the power switch (1). Two operat-
ing modes are available:
Temporary operation:
Press the power switch and slide
it towards the arrow until you
feel some resistance. The rotary
blade (6) runs as long as the
power switch is pressed and held
down in this position.
Continuous operation:
Press the power switch and slide
it towards the arrow beyond the
resistance point until it latches
into place. The rotary blade runs
without the power switch having
to be pressed and held down,
until you push the power switch
back into the "0" position.
Note:
Never use the appliance for more
than a maximum of 5 minutes in
continuous operation.
• With the appliance running,
gently feed the food to be sliced
into the path of the rotary blade.
• Once slicing has been com-
pleted, wait until the rotary blade
has come to a complete stop.
• After each use, turn the slice
thickness adjustment knob to the
"0" position, in order to cover up
the sharp rotating blade and to
avoid any injuries.
compact
1
/ no
1
Pull the slice tray (3) to the left
and out of the appliance.
CLEANING
Caution:
Switch the appliance o before
cleaning it; pull the power plug
out o the socket and turn the
slice thickness adjustment
knob (2) to the "0" position.
Clean the food slicer regularly
to prevent the accumulation of
food residue. The rotary blade
must also be cleaned regularly
as described below to prevent its
surface from rusting.
Note:
Over time, an accumulation of
food residue may cause damage
to the surface of the rotary blade,
causing it to rust.
Preparation
compact
1
/ no
1
• Pull the slice tray (3) to the left
and out of the appliance.
• Removing the left-over
holder (10).
Pull the slice carriage (9)
forward and then lift it up and out
of the guide groove.
Removing the rotary blade:
Open the blade catch (7), by
turning it in a clockwise direction.
• Take hold of the rotary
blade (6) at its rotational centre
and remove it.
English
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ritter sono1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ritter sono1 in the language / languages: All languages as an attachment in your email.

The manual is 1,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info