Manual Ritter E 118 (page 14 of 60) (English, German, Dutch, French, Italian, Polish, Spanish, Norwegian)

713296

Zoom out

Zoom in

1/60

Unfold the illustrations at the

front and back of this manual.

Please read these instructions

thoroughly before you start to

use the appliance. Keep these

operating instructions in a safe

place and ensure that they are

included with the appliance if

passing it on to a third party.

Alternatively, these operating

instructions are available at

www.ritterwerk.de.

INTENDED USE

The multi slicer is used to slice

household foods.

If the appliance is used for a

purpose other than this, or if it

is operated incorrectly, severe

injuries may occur or the

appliance may be damaged.

All warranty and liability claims

will be rendered null and void in

this case.

BEFORE USING THE

APPLIANCE FOR THE

FIRST TIME

Preparation

Before you use the appli-

ance for the rst time, have a

specialist install it in a suitable

drawer.

Clean the appliance before

allowing it to come into contact

with any food (see CLEAN-

ING).

Setting up the appliance

• Set the appliance down on a

at, non-skid surface close to a

mains socket.

Using a small amount of

force, push the slice car-

riage (8) vertically into the

guide groove on the appliance

until it audibly locks into place.

Slide the left-over holder (9)

onto the slice carriage's handle.

Unwind the mains cable (5)

to the length required from the

cable compartment (10) under

the appliance and insert the

mains plug into the socket.

SLICING

Use the slice thickness

adjustment knob (2) to set the

required thickness.

Note:

The slice thickness adjustment

scale is not a millimetre scale.

For safety reasons, the

"0" position is designed to

cover the blade.

Place the food to be sliced

onto the slice carriage (8). Use

the left-over holder (9) to press

it up against the stop plate (11).

Protect your hands, by

always using the slice carriage

and, where applicable, the left-

over holder. Exception: Exces-

sively large foods to be sliced.

Turn the appliance on using

the switch (1). Two operating

modes are available:

Temporary operation: Press

the switch and slide it towards

the arrow until you feel some

resistance. The rotary blade (6)

runs as long as the switch is

pressed and held down in this

position.

Continuous operation: Press

the switch and slide it towards

the arrow beyond the resist-

ance point until it latches into

place. The rotary blade runs

without the switch having to be

pressed and held down, until

you push the switch back into

the "0" position.

Note:

Never use the appliance

for more than a maximum

of 5 minutes in continuous

operation.

• With the appliance running,

gently feed the food to be

sliced into the path of the rotary

blade.

• When nished slicing, wait

until the rotary blade has come

to a complete stop.

• After each use, turn the slice

thickness adjustment knob

to the "0" position, in order to

cover up the sharp rotating

blade and to avoid any injuries.

Pull the slice tray (3) to the

right and out of the appliance.

CLEANING

Caution:

Switch the appliance off

before cleaning it; pull the

mains plug out off the socket

and turn the slice thickness

adjustment knob (2) to the

"0" position.

Clean the multi slicer regularly

to prevent the accumulation of

food residue. The rotary blade

must also be cleaned regularly

as described below to prevent

its surface from rusting.

Note:

Over time, an accumulation of

food residue may cause dam-

age to the surface of the rotary

blade, causing it to rust.

Preparation

• Remove the slice tray (3)

and the left-over holder (9).

Pull the slice carriage (8)

forward and then lift it up and

out of the guide groove.

Removing the rotary blade:

Place a suitable coin on the

blade catch (7) and turn it in an

anticlockwise direction.

• Take hold of the rotary blade

at its rotational centre and

remove it.

English

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ritter E 118 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish, Norwegian as an attachment in your email.

The manual is 1,36 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ritter E 118 Manual

Product: