744710
13
Zoom out
Zoom in
Previous page
1/14
Next page
|13
EN
12
Error
ERROR
#11
BURNBACK AND
FLUE GAS FLAP
FLUE GAS FLAP
OPEN
ERROR
#11
ERROR #12
FAN
DEFECT
No. #11 #11 #12
Meaning
Burn-back flap and flue gas flap are not
in heating position.
The flue gas flap is not in heating
position.
Prescribed speed of the flue gas fan is
not reached.
Solution
Quit error message and enable
burn-back flap and flue gas flap.
Close flue gas flap and quit error
message.
Quit error message.
Error
ERROR #13
NOT ENOUGH
LOW PRESURE
ERROR #14
STOVE
OVERHEATED
ERROR #14
STOVE
OVERHEATED
No. #13 #14 #14
Meaning
The pressure ratio between installation
room and firebox does not allow further
operation.
Heat accumulation inside the appliance
due to insufficient convection.
Heat accumulation inside the appliance
due to insufficient convection.
Solution
Quit error message and check the stove
for tightness (firebox door, cleaning lid),
disturbing factors in the installation
room (kitchen hood, windows closed,...),
as well as the flue.
Allow the stove to cool down and
disconnect it from the mains. Unblock
(press) the safety temperature limiter
(rear side of stove). Check if the
convection air openings are free.
Allow stove to cool down. Check if
all convection air openings are free.
Quit error message and check if
the convection air fan runs in the
CONTROLLED OPERATION operating
state.
Error
ERROR #15
COMM. DISCHARGE
BOARD
ERROR #16
COMM. INSERTION
BOARD
ERROR #17
COMM. AIR FLAPS
BOARD
No. #15 #16 #17
Meaning
The discharge motor cannot be
actuated properly.
The insertion motor cannot be actuated
properly.
The air flaps cannot be actuated
properly.
Solution
Allow stove to cool down. Interrupt
power supply for about 10 sec.
Allow stove to cool down. Interrupt
power supply for about 10 sec.
Allow stove to cool down. Interrupt
power supply for about 10 sec.
Error
STOVE NOT IN
END POSITION
ERROR
#18
TOUCH DISPLAY
DOES NOT RESPOND
ERROR
#19
ERROR #20
COMM. MAINBOARD
No. #18 #19 #20
Meaning
The mechanical pull-out lock of the
stove insert is not in (horizontal)
operating position.
Touchscreen is distorted. No further
entry is possible.
Connection to touch display is inter-
rupted.
Solution
Please check the safety lever of the
mechanical pull-out lock for correct
position and secure the stove.
Please contact the customer service.
Allow stove to cool down. Interrupt
power supply for about 10 sec.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rika Touch Display V2-23 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rika Touch Display V2-23 in the language / languages: English as an attachment in your email.

The manual is 2,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Rika Touch Display V2-23

Rika Touch Display V2-23 User Manual - German - 14 pages

Rika Touch Display V2-23 User Manual - Dutch - 14 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info