744710
10
Zoom out
Zoom in
Previous page
1/14
Next page
10
Current-free log operation
Note
Your stove must be disconnected from the mains for current-free
operation.
Note
Any modification of the procedure stated above may result in
damaging of components, which automatically will void any
warranty claims.
Insert the socket spanner supplied in the sleeve, as shown.
Turn it clockwise until a slight stop can be felt.
Remove the socket spanner from the opening and insert it again in
horizontal position.
Turn the spanner ant-clockwise until it is flush with the marking in
the side panel (approx. 45°). It is now in heating up position.
After heating-up has been successful, turn the spanner anti-
clockwise step by step to reduce the combustion air manually, thus
regulating the burn-off.
Each time logs are added, the spanner must be brought into heating
up positon again. The combustion air is regulated as described
above.
Note
Always ensure that the stove has enough air for combustion.
Combined operation
Automatic ignition of firewood during start-up, or automatic log
recognition during operation.
Automatic ignition of firewood during start-up
Place two logs into the firebox. Be sure that at least one of the logs
lies above the combustion trough to facilitate burning. Close firebox
door.
Start stove operation. After ignition has been successful, the
operating state IGNITION switches to LOG CHECK, and after
successful log recognition to LOG OPERATION.
Note
If no more logs are reloaded, pellet operation starts automatically
again as the unit is still on.
Automatic log detection during operation
Open the firebox door and place 2 logs into the box. Be sure that
at least one of the logs lies above the ignition trough to facilitate
burning.
Close firebox door. The operating state switches from CONTROLLED
OPERATION to LOG CHECK, and after successful log recognition to
LOG OPERATION.
Note
If no more logs are reloaded, pellet operation restarts automatically
as the unit is still on.
If you switch the combi stove off during log operation, the operating
state will change to STOVE OFF after the logs have burned down.
Easy-refilling operation
In order to reduce the discharge of fluegas when refilling logs there
is a easy-refilling operation available.
unhide additional
functions
hide additional
functions
Open the fluegas
flap
Wait about 3 seconds before you open the combustion chamber
door to refuel.
After closing the combustion chamber door, turn the wrench
clockwise to close the fluegasflap.
Tip
If the flue gas flap is open, a warning appears on the display. It
expires when you close the flue gas flap.
Note
Pellet operation is not possible with an opened flue gas flap.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rika Touch Display V2-23 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rika Touch Display V2-23 in the language / languages: English as an attachment in your email.

The manual is 2,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Rika Touch Display V2-23

Rika Touch Display V2-23 User Manual - German - 14 pages

Rika Touch Display V2-23 User Manual - Dutch - 14 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info