744638
14
Zoom out
Zoom in
Previous page
1/24
Next page
14
6. OPERATION - RIKATRONIC3
Note
For stoves with RIKATRONIC3 System (electronic
air flap control) a flue pipe with optional “lockable
damper flap” must be always open during heating!
RISK OF FIRE!
Each combustion process needs oxygen� Before ignition the
combustion chamber must be regularly cleaned from ash to ensure
an adequate supply of air
The right fill amount for heating up is 2 - 3 logs of the quantity given
in AMOUNT OF FUEL
Correct heating up primarily according to instructions counteracts
excessive smoke during heating up
RIKA firelighter
Always ignite the RIKA firelighter on the red tip� One block consists
out of 8 ribs which can be divided to the desired size� The amount
of RIKA firelighters also depends on the size and humidity of your
firewood� Ideally, one rib is enough to light up the fire
Tip
You can order the RIKA firelighter with the number E15834 at your
RIKA dealer
Heating instructions
Preparation
Plug in the mains plug and activate the main switch at the rear of
the stove� The main switch now lights up green� The display at the
front of the stove also lights up green for approx� 10 secs� and then
flashes intermittently red until the air flap motor reference run has
been completed�
Correct heating up
When the display is constantly red, open the combustion chamber
door and sweep the ashes into the ashtray� Place left and right 2 small
pieces of chipboard lengthways in the bottom of the combustion
chamber and open the riddle grate completely�
Place 2 – 3 smaller (highly flammable) logs crossways on top of this
chipboard�
Now place further pieces of chipboard in crossways layers on top of
the logs and ideally you should place 2-4 ribs of the RIKA-firelighter
on top of the chipboard� Some uncoated paper can be placed
underneath the chipboard in case there is no firelighter available�
Now light the firelighter (or the uncoated paper) and close the
combustion chamber door
As soon as the combustion chamber temperature exceeds 80°C,
the display changes to green (if the display does not change to
green within 10 min of closing the combustion chamber door, then
the heating up procedure has failed, i�e� the required combustion
chamber temperature of 80°C was not exceeded)�
Once the display has changed to green, the burn-off control of
the heating-up starts� The heating-up phase takes approx� 60 min
depending on the temperature and fill amount� This time is required
to obtain a suitable bed of embers�
The display changing from green to red flashing indicates the right
time to add wood�
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rika Look RLU at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rika Look RLU in the language / languages: English as an attachment in your email.

The manual is 6,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Rika Look RLU

Rika Look RLU User Manual - German - 24 pages

Rika Look RLU User Manual - Dutch - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info