643290

Riello BGK0.1 Manual

39
Zoom out
Zoom in
Previous page
1/52
Next page
2922
7
GB
PUMP PRESSURE
The pump leaves the factory set at 12 bar.
To change it act on pump pressure adjust screw (5, fig.
7, page 4).
COMBUSTION HEAD SETTING (see fig. 14)
It depends on the output of the burner and is carried out
by rotating clockwise or counterclockwise the setting
screw (2) until the set-point marked on the regulating
rod (3) is level with the outside plane of the diffuser noz-
zle-holder assembly (1).
– In the sketch the combustion head is set for an output
of 0.65 GPH at 12 bar.
The set-point 3 of the regulating rod (3) is at the same
level with the outside plane of the nozzle-holder
assembly (1) as shown in the schedule.
AIR DAMPER ADJUSTMENT (see fig. 14)
To vary the setting adjust the screw (4) after loosing the
nut (5).
When burner shuts down the air damper automatically
closes till a max. chimney depressure of 0.5 mbar.
4.3 POSITIONING OF THE OPTICAL FIBRE, (see fig. 15)
To position the optical fibre, you must proceed as follows:
➤ Insert optical fibre (1) in the diffuser disc support assembly (3), making sure it is pushed in all the way.
➤ Tighten screw (4) carefully to hold optical fibre (1) in place.
4.4 ELECTRODES ADJUSTMENT (see fig. 15)
4.5 FUEL HEATING
In order to assure regular ignition and working also at low temperature the burner has an oil pre-heater fitted in
combustion head. The pre-heater starts when thermostats close.
When the required temperature for ignition is reached the thermostat fitted on the nozzle holder starts the burn-
er. The pre heater remains energised during working and cuts out when burner shuts-down.
S7717
Fig. 14
2
1
3
1
5
4
2
3
4
MEASURES MUST BE
RESPECTED.
WARNING
Lean the diffuser disc-holder as-
sembly (3) on the nozzle-holder
(2) and lock it by screw (4).
For prospective adjustments of
the electrodes assembly (5), loo-
sen screw (6).
To have access to the electro-
des carry out operation as de-
scribed in chapter 4.1 (page 6)
“RECOMMENDED NOZZLES”.
D4222
Fig. 15
4.5 – 0.5 mm
0
3.5 mm
5.5 mm
41
2
5 6
3
… 39 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Riello BGK0.1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Riello BGK0.1 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 0,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info