780476

Ridley Mountain Bike Manual

22
Zoom out
Zoom in
Previous page
1/42
Next page
22
(4) Put the chain on top of the smallest freewheel sprocket. Then,
insert the wheel into the frame dropouts and pull it all the way in to
the dropouts (Fig. 14).
(5) Tighten the adjusting nut until it is tight against the frame dropout;
then rotate the lever toward the front of the bike until it is parallel to
the frame's chainstay or seatstay tube and is curved toward the
wheel (Fig. 14).
CAUTION: If you can fully close the quick release without wrapping
your fingers around the chainstay/seatstay tube for leverage, and the
lever does not leave a clear imprint in the palm of your hand, the
tension is insufficient. Open the lever, turn the tension adjusting nut
clockwise a quarter turn, and then try again.
(6) If the lever cannot be pushed all the way to a position parallel to
the chainstay or seatstay tube, return the lever to the OPEN position.
Then turn the adjusting nut counterclockwise one-quarter turn and try
tightening again.
(7) Push the rear derailleur back into position.
(8) Close the brake shoes; then spin the wheel to make sure that it is
centered in the frame and clears the brake shoes.
6.1.4. Removing and Installing Bolt-On Wheels
6.1.4.a. Removing a Bolt-On Front Wheel
(1) Open up the brake
(2) With a 15mm box wrench or a six-inch adjustable wrench, loosen
the two axle nuts.
(3) If your front fork has a clip-on
type secondary retention device,
disengage it and go to step (4). If
your front fork has an integral
secondary retention device, loosen
the axle nuts about six full turns;
then go to step (4).
(4)Raise the front wheel a few inches off the ground and tap the top
of the wheel with the palm of your hand to knock the wheel out of the
fork ends.
6.1.4.b. Installing a Bolt-On Front Wheel
(1) With the steering fork facing forward, insert the wheel between
the fork blades so that the axle seats firmly at the top of the slots that
are at the tips of the fork blades. The axle nut washers should be on
the outside, between the fork blade and the axle nut. If your bike has
a clip-on type secondary retention device, engage it.
… 22 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ridley Mountain Bike at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ridley Mountain Bike in the language / languages: English as an attachment in your email.

The manual is 1.64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info