104116
135
Zoom out
Zoom in
Previous page
1/155
Next page
133
Appendix
Error Messages
If an error message is displayed on the LCD monitor or LCD panel, follow the
procedures below.
Error Message
CARD ERROR
Insufficient memory
UNMATCHED FILE
NO FILE
No card
Cannot open the file
Cannot open the file
On-screen keypad error
Cannot reset the system
Format failed
Failed to save Keypad memo
Pen-memo Error: memory over
Select ERASE ALL, SAVE or CANCEL
Too many pen-memo data in memory
File number exceeded limit
No file for DPOF setting
Standard Print Number over
Select image and set Standard Print
Number to 0.
DPOF file set error
DPOF file read error
Remedy
This type of card is not supported by the camera. Use another
type of card.
Card memory or internal memory is full and no more files can be
recorded. Erase unwanted files or use another card.
Unplayable file was selected.
No recorded files in specified folder. Change folder or select
storage memory that contains files.
Card of selected type not found. Insert card.
Recorded file cannot be displayed. Return to previous screen and
repeat operation. If file is still not displayed, switch power off and
repeat operation.
Recorded file cannot be saved. Check available capacity of
storage memory and repeat operation. If image still cannot be
saved, switch power off and repeat operation.
On-screen keypad cannot be displayed. Repeat operation. If
keypad is still not displayed, switch power off and repeat
operation.
Switch off power again. If camera is still not reset, remove battery
and switch power on, then reload battery and repeat operation.
Repeat format operation again. If storage memory still cannot be
formatted, problem lies with storage memory. Use another
storage memory.
Failed to save keypad memo. Repeat operation.
Erase or save all pen memos, or cancel pen memo operation.
No more pen memos can be saved. Delete unwanted memos
before saving.
File number exceeded limit. Delete unnecessary files or use
another memory card.
There is no image file for setting DPOF in folder. Select folder
including image files.
Number of specified images has exceeded limit. Reduce number
of specified images.
DPOF settings cannot be saved. Delete all unnecessary files
before repeating operation. If message still appears, memory may
be damaged. Make a backup file of files saved in memory and
format memory.
DPOF settings are unreadable. Reset all DPOF settings before
repeating operation. If message still appears, memory may be
damaged. Make a backup file of files saved in madia and format
memory.
Note
If the error message continues to be displayed after the above
procedures have been followed, open the terminal cover and press the
reset switch (P.6) with the tip of a propelling pencil or similar object.
The settings will return to the factory default settings.
If the error message is still displayed, contact the store where
purchased or your nearest Ricoh service office.
135


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ricoh RDC-I 700 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ricoh RDC-I 700 in the language / languages: English as an attachment in your email.

The manual is 1,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info