639315
196
Zoom out
Zoom in
Previous page
1/206
Next page
182
9. Appendix
Troubleshooting
This section helps you resolve problems you may encounter while setting up or using the projector.
Indicator Messages
Power Indicator
Indicator Condition Projector Condition Note
Off The main power is off
Blinking light Blue 0.5 sec On,
0.5 sec Off
The projector is getting ready to turn on. Wait for a moment.
2.5 sec On,
0.5 sec Off
Off Timer is enabled.
Orange 2.5 sec On,
0.5 sec Off
On Timer is working.
0.5 sec On,
0.5 sec Off
After cooling.
Steady light Blue The projector is turned on.
Orange [NORMAL] or [NETWORK STANDBY] is selected
for [STANDBY MODE]
Red [POWER-SAVING] is selected for [STANDBY
MODE]
Status Indicator
Indicator Condition Projector Condition Note
Off
Normal or Standby ([POWER-SAVING] or [NET-
WORK STANDBY] for [STANDBY MODE])
Blinking light Red 1 cycle (0.5 sec
On, 2.5 sec Off)
Lamp cover error or lamp unit error Replace the lamp cover or lamp unit correctly.
2 cycle (0.5 sec
On, 0.5 sec Off)
Temperature error The projector is overheated. Move the projector to
a cooler location.
3 cycle (0.5 sec
On, 0.5 sec Off)
Power error Power unit is not working properly. Contact your
dealer.
4 cycle (0.5 sec
On, 0.5 sec Off)
Fan error Fans will not work correctly.
6 cycle (0.5 sec
On, 0.5 sec Off)
Lamp error Lamp fails to light. Wait a full minute and then turn
on again.
Orange
1 cycle (0.5 sec
On, 2.5 sec Off)
Network conflict
Both the built-in wired LAN and the wireless LAN
cannot be connected to the same network at the
same time.
To use both built-in wired LAN and wireless LAN at
the same time, connect them to different networks.
Green Re-firing the lamp (The projector is cooling
down.)
The projector is re-firing.
Wait for a moment.
Steady light
Green
Standby ([NORMAL] for [STANDBY MODE])
Orange CONTROL PANEL LOCK is on. You have pressed cabinet button when Control
Panel Lock is on.
CONTROL ID error Remote control ID and projector ID are not
matched.
Lamp Indicator
Indicator Condition Projector Condition Note
Off Normal
Blinking light Red
Lamp has reached its end of life� Lamp replace-
ment message will be displayed�
Replace the lamp.
Steady light Red Lamp has been used beyond its limit. The projector
will not turn on until the lamp is replaced.
Replace the lamp.
Green [LAMP POWER] is set to [ECO1] or [ECO2]
Over-Temperature Protection
If the temperature inside the projector rises too high, the over-temperature protector will automatically turn off the lamp
with the Status indicator blinking (2-cycle On and Off.)
Should this happen, do the following:
Unplug the power cord after the cooling fans stop.
Move the projector to a cooler location if the room where you are presenting is particularly too warm.
Clean the vents if they are clogged with dust.
Wait about 60 minutes until the inside of the projector becomes cool enough.
196


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ricoh PJ WX5361N at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ricoh PJ WX5361N in the language / languages: English as an attachment in your email.

The manual is 21,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Ricoh PJ WX5361N

Ricoh PJ WX5361N User Manual - German - 205 pages

Ricoh PJ WX5361N User Manual - Dutch - 208 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info