639324
262
Zoom out
Zoom in
Previous page
1/268
Next page
247
10. Appendix
Common Problems & Solutions
( “Power/Status/Lamp Indicator” on page 245.)
Problem Check These Items
Does not turn on
or shut down
Check that the power cord is plugged in and that the power button on the projector cabinet or the remote control
is on. ( pages 15, 16)
Ensure that the lamp cover is installed correctly. ( page 177)
Check to see if the projector has overheated. If there is insufficient ventilation around the projector or if the room
where you are presenting is particularly warm, move the projector to a cooler location.
Check to see if you continue to use the projector for another 100 hours after the lamp has reached the end of
its life. If so, replace the lamp. After replacing the lamp, reset the lamp hours used. ( page 129)
The lamp may fail to light. Wait a full minute and then turn on the power again.
Set [FAN MODE] to [HIGH ALTITUDE] when using the projector at altitudes approximately 5500 feet/1700 meters
or higher. Using the projector at altitudes approximately 5500 feet/1700 meters or higher without setting to [HIGH
ALTITUDE] can cause the projector to overheat and the projector could shut down. If this happens, wait a couple
minutes and turn on the projector. ( page 110)
If you turn on the projector immediately after the lamp is turned off, the fans run without displaying an image
for some time and then the projector will display the image. Wait for a moment.
Will turn off Ensure that the [OFF TIMER], [AUTO POWER OFF] or [PROGRAM TIMER] is off. ( page 113, 128)
No picture Check if the appropriate input is selected. ( page 18) If there is still no picture, press the INPUT button or one
of the input buttons again.
Ensure your cables are connected properly.
Use menus to adjust the brightness and contrast. ( page 89)
Ensure that the lens cover is open. ( page 16)
Reset the settings or adjustments to factory preset levels using the [RESET] in the Menu. ( page 129)
Enter your registered keyword if the Security function is enabled. ( page 36)
If the HDMI input or the DisplayPort signal cannot be displayed, try the following.
- Reinstall your driver for the graphics card built in your computer, or use the updated driver.
For reinstalling or updating your driver, refer to the user guide accompanied with your computer or graphics
card, or contact the support center for your computer manufacturer.
Install the updated driver or OS on your own responsibility.
We are not liable for any trouble and failure caused by this installation.
Both the composite video signal from each input connector as the computer, BNC, and BNC (CV), and the S-video
signal from the BNC (Y/C) Input connector are not output from HDMI OUT Connector of this projector.
Be sure to connect the projector and notebook PC while the projector is in standby mode and before turning on
the power to the notebook PC.
In most cases the output signal from the notebook PC is not turned on unless connected to the projector before
being powered up.
* If the screen goes blank while using your remote control, it may be the result of the computer’s screen-saver
or power management software.
• See also the page 249.
Picture suddenly
becomes dark
Check if the projector is in the Forced ECO mode because of too high ambient temperature. If this is the case,
lower the internal temperature of the projector by selecting [HIGH] for [FAN MODE]. ( page 110)
Color tone or hue is
unusual
Check if an appropriate color is selected in [WALL COLOR]. If so, select an appropriate option. ( page 110)
Adjust [HUE] in [PICTURE]. ( page 90)
Image isn’t square to
the screen
Reposition the projector to improve its angle to the screen. ( page 20)
Perform [GEOMETRIC CORRECTION] when the trapezoid is distorted. ( page 100)
Picture is blurred Adjust the focus. ( page 22)
Reposition the projector to improve its angle to the screen. ( page 20)
Ensure that the distance between the projector and screen is within the adjustment range of the lens.
( page 233)
Has the lens been shifted by an amount exceeding the guaranteed range? ( page 236)
Condensation may form on the lens if the projector is cold, brought into a warm place and is then turned on.
Should this happen, let the projector stand until there is no condensation on the lens.
Flicker appears on
screen
Set [FAN MODE] to other than [HIGH ALTITUDE] mode when using the projector at altitudes approximately 5500
feet/1700 meters or lower. Using the projector at altitudes less than approximately 5500 feet/1700 meters and
setting to [HIGH ALTITUDE] can cause the lamp to overcool, causing the image to flicker. Switch [FAN MODE] to
[AUTO]. ( page 110)
Image is scrolling
vertically, horizontally
or both
Check the computer’s resolution and frequency. Make sure that the resolution you are trying to display is sup-
ported by the projector. ( page 237)
Adjust the computer image manually with the Horizontal/Vertical in the [IMAGE OPTIONS]. ( page 91)
262


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ricoh PJ WU6181N at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ricoh PJ WU6181N in the language / languages: English as an attachment in your email.

The manual is 17,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Ricoh PJ WU6181N

Ricoh PJ WU6181N User Manual - German - 269 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info