793415

Respekta CH1259IXCN - Tilla Manual

28
Zoom out
Zoom in
Previous page
1/29
Next page
1. Preparations
2. Wall mounting
English
Operating- and Installation Instruction Cooker Hood
18. GENERAL INSTALLATION INSTRUCTIONS STANDARD HOODS
a) Using the supplied drilling template, drill the wall holes (4 holes 8
mm) (Fig. 4)
b) Insert the plugs in the drilled holes.
c) Screw 2 screws into the top plugs up to ca.5 mm.
d) Hang the hood on the screws (Fig. 5)
e) From the inside, pass the locking screws through the rear wall of
the hood and screw securely in the bottom plugs (Fig.6)
a) Determine the exact location for the hood.
b) Provide the power supply at the correct location.
c) Now decide on the mode of operation (circulation or exhaust air
mode) and prepare the hood accordingly .(Fig.1)
If you have decided upon exhaust air mode, all the appropriate core
holes for routing the exhaust air hose must be executed or already
present.
(Fig. 2) shows the different variants for core holes and the
dimensions in mm to be observed.
d) Remove the inlet air mesh (Fig. 3a) resp. grease filter (Fig. 3b) for
later access to the inside of the hood.
e) Mount the flange (Fig. 1 A) to the opening through which the
exhaust air is to be taken. (Where necessary change over the
positions of the plastic cap (Fig. 1 B) and the flange (A)
3. Mounting to a wall unit (where intended for this)
Drill the underside of the wall unit using the drilling template.
Fix the hood inside the wall unit with 4 screws (Fig. 7).
In the case of exhaust air hoods, an opening must be made in the
wall unit for the exhaust air pipeline.
Circulation air hoods do not require this opening because with these
the air is circulated through the slots at the front of the hoods.
Images are for illustration purposes only.
The form and fittings of your hood can vary from the illustrations.
4. Circulation air mode : Mount the carbon filter (Fig. 8) when using
the circulation air mode.
5. Mounting the exhaust air hose: The exhaust air hose is mounted
to the flange (Fig. 1 A) with a metal hose clip.
see chapter 11.1
GB
fi200812atl
12
… 28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Respekta CH1259IXCN - Tilla at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Respekta CH1259IXCN - Tilla in the language / languages: English, German as an attachment in your email.

The manual is 1.69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info