Manual Respekta CH 99060 SA (page 7 of 9) (English, German)

793466

Zoom out

Zoom in

1/9

Content:

Page

Mounting the V-Flap 2

Installation of the hood for

recirculation mode

2 - 3

Mountin

the hood for exhaust

air o

eration

Before beginning, make sure the power supply is secure. This must be set up by a specialist.

Attention! Before installing the hood, insert the V-Flaps as described below:

Montage der Ventilklappen:

If the valve flaps are not factory-mounted:

• First install half part 1 in connection nozzle B10

• Pins 3 must be in upwards position.

• Insert the axle 4 into the holes 5 on the nozzle B10.

• Repeat all operations for mounting the half part 2.

Montage der Haube für Umluftbetrieb: (Fig. are for Illustration only)

8. Place the lower chimney shaft on the hood.

1. Using pencil, draw a horizontal line at the height on the wall on which the hood

bottom edge should lie. (It is best to use a water level) Attention! Observe minimum

distance according to chapter 11.1 of the operating instructions.

2. Hold the supplied drill template with the bottom edge on the drawn pencil line

against the wall and mark the four drill holes. (Fig. a)

3. Drill a 30mm deep hole in the wall with an 8mm masonry drill at the 4 pencil marks.

For safety, check the diameter of the plugs with a caliper gauge.

4. Place one plug into each of the 4 holes.

5. Screw a ST4 × 30mm screw into the two upper dowels (Fig. a) Attention! The

screw heads must protrude 3 - 5 mm out of the dowels so that the hood can be

hanged on them. (maybe readjust)

6. Hang the hood with the two eyelets on its back (Fig. b) by the two screws on the

wall.

7. Mount the stabilizer- and mounting plate at the top of the lower flue with two ST4 *

8mm screws (Fig. c)

9. Firmly press the chimney shaft against the wall and mark with pencil the two drill

holes through the holes in the chimney stabilize- and mounting plate. (Fig. d)

10. Remove the chimney from the hood.

11. Drill two 40mm deep holes into the wall at the marked locations using an 8mm

masonry drill.

12. Push the upper (inner) chimney shaft from above into the lower (outer) chimney

shaft.

13. Place the nested chimneys on the hood.

Fig. a)

Fig. d)

Fig. b)

Fig. c)

fi200728ATL 2/4

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Respekta CH 99060 SA in the language / languages: English, German as an attachment in your email.

The manual is 0.56 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Respekta CH 99060 SA Manual

Product: