793401

Respekta CH 22010-90 WB Svea Manual

20
Zoom out
Zoom in
Previous page
1/24
Next page
English Operating instructions / users manual Cooker Hoods
7
G
B
Is the air taken from the kitchen being replaced by
sufficient fresh air, so that no partial vacuum is
being produced in the room?
The lighting fails to function:
Does the lamp need changing?
Has the lamp been properly fitted and seated in
the holder up to the stop?
Is the fuse blown or has the circuit breaker tripped
out?
If all the above checks fail to remedy the fault,
it is possible you have a more serious problem.
In no circumstances try to repair the
electronic/electrical components in the appliance.
Contact your Customer Service.
10. Customer Service
For technical queries concerning your appliance
please contact the customer service office of your
dealer.
Before calling the customer service please note
Model/Type of your appliance.
The type and rating plate is located inside the
appliance (remove the grease filter)
11. Installation
Before installation of the appliance
please pay regard to:
Installation of the appliance only at a convenient
place.
Check the wall / ceiling on sustainability and
resilience.
Check the routing of electrical and other
conductions in and on the wall respectively ceiling,
in order to not damage them with the drill.
Check the condition and resilience of electric
conduction.
We recommend the installation of the appliance by
a professional.
On installation, the minimum distance between the
hob and the hood must be exactly complied with (see
chapter 11.1 “Installation data“) and follow the
numbering of the steps and the additional
instructions. Execution with air exhausted outdoors
(A- see also the installation data). The vapours are
extracted via an air exhaust hose fixed to the
connector ring.
The diameter of the exhaust air hose must conform
to that of the connector ring. If a smoke non-return
valve is used or is planned, check whether it can
open and close freely after the installation of the
exhaust air hose. The extractor hood can be
fi191007atNEG
equipped with one (top) or two (top and back)
extractor openings.
The hood is normally initially fitted out for use of the
top extractor opening, as an extractor hood.
Openings not required are fitted with a plastic cover.
This plastic cover can be easily removed by turning
counterclockwise and optionally fitted to another
opening which is not required.
11.1 Installation data
Minimum distance from the lower edge of the hood
body:
to ceramic and cast cooking hobs 65 cm
to gas hob 70 cm
to hobs with coal/oil/wood firing 85 cm.
Only connect the appliance to the power
supply once it is properly installed.
11.2 Using the extractor hood as an exhaust air
hood (with air extracted to outdoors)
If the extractor hood has been fitted at the factory with
a carbon filter, this must be removed.
It is only practicable to use this when operating your
hood in circulation mode.
11.3 Converting the extractor hood to a
circulation hood
If you wish to use an appropriately fitted hood as a
circulation hood, you must mount the active carbon
filter(s) to the fan motor before using the hood.
The active carbon filter(s) is/are included in the scope
of supply with some models.
Otherwise you must obtain the active carbon filter(s)
from the supplier of your extractor hood.
You must also change your hood over to the “Filter
position“ at the device provided (lever or ball
handle) inside of the hood.
11.4. Electrical connection
Before connecting the extractor hood, check
that the voltage stated on the rating plate (V) agrees
with the supply voltage in your home.
Never install the appliance if the data on the
rating plate does not agree with your supply voltage.
You will find the rating plate inside the appliance,
behind the grease filter.
If the extractor hood is fitted with a standard
connector plug, connect this to an easily accessible
standard socket.
11.5 Mounting the carbon filter (not included
in the scope of supply)
You will find the mounting instructions for the carbon
filter in its packaging. To mount the carbon filter,
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Respekta CH 22010-90 WB Svea at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Respekta CH 22010-90 WB Svea in the language / languages: English, German as an attachment in your email.

The manual is 2.13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info