793456
7
Zoom out
Zoom in
Previous page
1/9
Next page
Content:
Page
Mounting the V-Flap 2
Installation of the hood for
recirculation mode
2 - 3
Mountin
g
the hood for exhaust
air o
p
eration
4
Before beginning, make sure the power supply is secure. This must be set up by a specialist.
Attention! Before installing the hood, insert the V-Flaps as described below:
Montage der Ventilklappen:
If the valve flaps are not factory-mounted:
• First install half part 1 in connection nozzle B10
• Pins 3 must be in upwards position.
• Insert the axle 4 into the holes 5 on the nozzle B10.
• Repeat all operations for mounting the half part 2.
Montage der Haube für Umluftbetrieb: (Fig. are for Illustration only)
8. Place the lower chimney shaft on the hood.
1. Using pencil, draw a horizontal line at the height on the wall on which the hood
bottom edge should lie. (It is best to use a water level) Attention! Observe minimum
distance according to chapter 11.1 of the operating instructions.
2. Hold the supplied drill template with the bottom edge on the drawn pencil line
against the wall and mark the four drill holes. (Fig. a)
3. Drill a 30mm deep hole in the wall with an 8mm masonry drill at the 4 pencil marks.
For safety, check the diameter of the plugs with a caliper gauge.
4. Place one plug into each of the 4 holes.
5. Screw a ST4 × 30mm screw into the two upper dowels (Fig. a) Attention! The
screw heads must protrude 3 - 5 mm out of the dowels so that the hood can be
hanged on them. (maybe readjust)
6. Hang the hood with the two eyelets on its back (Fig. b) by the two screws on the
wall.
7. Mount the stabilizer- and mounting plate at the top of the lower flue with two ST4 *
8mm screws (Fig. c)
9. Firmly press the chimney shaft against the wall and mark with pencil the two drill
holes through the holes in the chimney stabilize- and mounting plate. (Fig. d)
10. Remove the chimney from the hood.
11. Drill two 40mm deep holes into the wall at the marked locations using an 8mm
masonry drill.
12. Push the upper (inner) chimney shaft from above into the lower (outer) chimney
shaft.
13. Place the nested chimneys on the hood.
Fig. a)
Fig. d)
Fig. b)
Fig. c)
fi200728ATL 2/4
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Respekta CH 2060 SBM at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Respekta CH 2060 SBM in the language / languages: English, German as an attachment in your email.

The manual is 0.56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info