Manual Renkforce T-701B (page 3 of 8) (English, German, Dutch, French)

491271

Zoom out

Zoom in

1/8

Installation

The monitor can be set up using the foot enclosed or installed in a headrest or installation opening, e.g. in a

caravan, using the mounting frame.

Please select the place of installation carefully so that the device neither inﬂ uences the

driver’s activity nor distracts him from the trafﬁ c.

Do not install any components within the range of the fully-expanded airbag, as this could

lead to injury to the vehicle‘s occupants in the event of an accident.

Modiﬁ cations to the vehicle which are made necessary through the installation of the

monitor or other components must always be carried out in such a manner that neither

the trafﬁ c safety nor the designed stability of the car is impaired. With many vehicles, the

MOT will be void, if you cut out a section of the sheet metal.

Before drilling the attachment holes, make sure that the electric cables, brake lines, the

fuel tank or similar systems will not be damaged.

When installing the monitor, take into consideration the risks that can arise from devices

being dismounted in the event of an accident. Therefore mount it safely and in a place

where it cannot become a danger for the passengers.

• Push the two enclosed plastic wedges between monitor and mounting frame in the area of the retaining

brackets.

• Pull the monitor out of the mounting frame.

Installing the foot

• Attach the foot to the installation surface with the adhesive pad included in the delivery or use suitable

screws.

• If you decide to use the adhesive pad for mounting the foot, clean the mounting surface with a suitable

cleaning agent before you start. Please note that the temperature must be at least 15 °C when using the

adhesive pad.

• The mounting surface on the foot can be bent and thus, adjusted to possible curves in the set up area.

• Push the monitor with the fastening rail on the back of the housing onto the foot and carefully tighten the

clamping screw.

• The angle of the monitor can be adjusted with the second screw on the foot.

Installation

• Cut out a mounting opening of 177 x 120 mm. The required mounting depth is 18 mm.

• Glue the mounting frame onto the mounting surface or bolt it down. For this purpose, the mounting frame

provides corresponding holes.

☞

Turn the mounting frame so that the opening for the connection cable is on the bottom right.

• After completion of the connection work (see next chapter), insert the monitor into the mounting frame and

snap it into place.

Connection

The electric connection should always be carried out by a specialist.

To avoid short-circuits and resulting damages of the device, the negative pole (ground) of

the vehicle battery must be disconnected during connection.

Before reconnecting the negative terminal to the battery, ensure that the device has been

completely connected.

Only use a volt meter, or a diode test lamp, to check the voltage of the vehicle system

leads, as normal test lamps consume excessive voltage and may thus damage the vehi-

cle‘s electronics.

When installing the cables, ensure that these are not squashed or scraped on sharp edges.

Use rubber grommets at cable gland points.

+12V

• Connect the combined connector of the connecting cable enclosed to the corresponding socket on the

monitor.

• Connect the yellow RCA connector VIDEO 1 IN (yellow wire) to the video output of your playback device.

• Connect the red RCA connector AUDIO IN to the audio output of your playback device.

• Connect the yellow RCA connector VIDEO 2 IN (white wire) to the video output of another playback device

or the video output of your reversing camera.

• Connect the black cable GND to the vehicle’s ground.

• Connect the red +12 V cable to a connector that only carries +12 V while the ignition is switched on.

☞

Do not connect this terminal to continuous current, otherwise the on-board battery could be dis-

charged when the vehicle is parked for a longer period of time.

• If you have connected a reversing camera to the connector VIDEO 2 IN, connect the green cable “reversing

wire” to the terminal that carries +12 V when the reverse gear is engaged.

☞

This cable automatically switches the video input to the VIDEO 2 IN input (signal of the reversing

camera) if the reverse gear is engaged. It can be connected to the cable of the reversing light,

for example.

• If you wish to connect a playback device to the monitor temporarily only, connect its AV output to the adapter

cable enclosed (yellow = video, red = audio).

• Plug the phone jack of the adapter cable into the AV IN input (6) on the front of the monitor.

☞

The connector VIDEO 1 IN will be deactivated as long as the adapter cable is plugged in.

• If you wish to use a headset, plug its connecting cable into the headphone (7) connector on the front of the

monitor.

☞

The inbuilt loudspeaker of the monitor will be deactivated as long as the headset is plugged in.

╞

OPERATING INSTRUCTIONS

T-701B 17,8 cm (7”) Monitor

Item no. 37 39 65

Intended use

The monitor is used to play back audio and video signals of externally connected devices in vehicles.

This product is only approved for the connection to 12 V direct current on-board networks with the negative

pole of the battery to the car body. The product may only be installed and operated in vehicles with this kind

of on-board voltage.

The user must make sure that the way the product is installed protects the product from humidity and wetness.

Any use other than the one described above damages the product. Moreover, this involves dangers such as

short-circuit, ﬁ re, electric shock, etc..

No part of the product should be modiﬁ ed or reassembled.

This product complies with the national and European legal requirements.

Always follow the safety instructions.

Safety Instructions

The warranty will be void in the event of damage caused by failure to observe these safety

instructions! We do not assume liability for any resulting damage.

We do not assume any liability for material and personal damage caused by improper use

or non-compliance with the safety instructions. In such cases, the warranty will be null and

void.

An exclamation mark inside a triangle points out important instructions in the operating

manual.

☞

The “hand” symbol indicates special information and advice on operating the device.

• Extra care should be taken when using the device for the ﬁ rst time. Therefore, please follow the operating

instructions carefully.

• In many countries, the use as a monitor to play back movies etc. while driving is only allowed for car pas-

sengers. The driver must not be distracted by this. Prior to the installation, ask for information about the

statutory regulations in your country.

• For safety reasons, any unauthorised conversion and/or modiﬁ cation to the product is not permitted.

• The device may only be used with the 12 V DC vehicle power supply (with the negative terminal of the

battery connected to the body of the vehicle). Never connect the device to a different power supply.

• This product is not a toy, it is not suitable for children. Children are not aware of the potential dangers

involved when using electrical devices.

• Do not expose the device to high temperatures, dripping or splashing water, strong vibrations or heavy

mechanical stress.

• Check the device occasionally for damage. Should the device show any sign of damage, do not use it

anymore. Disconnect the device from the power supply (remove the batteries) and take it to a specialist

service centre.

• Only use the device in a temperate climate, never in a tropical climate.

• Do not leave packaging materials unattended. They may become dangerous playthings for children.

• Also observe the safety and operating instructions of any other devices that are connected to this device.

• Please observe the additional safety instructions in the individual chapters of this manual.

• If in doubt about how to connect the device correctly, or should any questions arise that are not answered

in these operating instructions, please contact our technical advisory service or another specialist.

Inserting/changing the batteries of the remote control

Keep batteries out of the reach of children.

Make sure that the polarity is correct when inserting the battery.

Remove the battery when the device will not be used for a while.

Leaking or damaged batteries can lead to caustic burning of the skin. Therefore, use suit-

able protective gloves.

Make sure that the battery is neither short-circuited nor thrown into a ﬁ re. Do not recharge

batteries. There is danger of an explosion.

• Pull out the battery holder on the backside of the remote control.

• Remove the discharged battery and insert a new 3 V lithium CR2025 coin cell. The correct polarity is indi-

cated on the battery holder.

• Slide the battery compartment cover on to the remote control again. It must snap in place.

• If the remote control no longer functions properly, the battery is discharged and must be replaced by a new

one of the same type.

Version 05/12

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Renkforce T-701B in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,86 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Renkforce T-701B Manual

Product: