692203
33
Zoom out
Zoom in
Previous page
1/62
Next page
33
8
Zurück im Menü < Preheat > < Turn off > auswählen.
Der Heizvorgang des Extruders ist beendet.
Statt der Solltemperatur, wird nun < OFF > (aus)
angezeigt.
Filamentrückstände von der Düse mit der Pinzette
entfernen.
Wenn das Filament sich von oben aus dem
Extruder herausziehen lässt, den Vorgang mit <
Stop > beenden.
Ziehen Sie das Filament mit dem
Filamentschlauch vorsichtig von oben aus dem
Extruder heraus.
7
e) Filament wechseln / ersetzen
Wechseln Sie das Filament, wenn Sie eine andere Filamentfarbe oder ein anderes Material wünschen.
Wenn das bisherige Filament verbraucht ist, tauschen Sie das Filament durch ein neues aus.
Vor dem Ändern oder Ersetzen des Filaments muss zuerst der Extruder erhitzt werden, damit das alte Filament
rückstandsfrei am Extruder ausgetauscht werden kann.
Berühren Sie die Düse auf keinen Fall. Verbrennungsgefahr!
Entnehmen Sie das Filament.
Nehmen Sie die Filamentspule aus der Spulenhalterung und bringen Sie das neue Filament an der
Spulenhalterung an.
Richten Sie das Filament ein.
Ziehen Sie das Filament ein.
Lassen Sie das neue Filament extrudieren, bis die Rückstände vom alten Filament komplett aus dem Extruder
beseitigt sind. Dies lässt sich anhand der Farbänderung erkennen.
Entfernen Sie die Rückstände mit der Pinzette.
f) Installation der „Cura“ Software (optional)
EinzelheitendazundenSieimKapitel„16. Mit der „Cura“ Software drucken“ auf Seite 39.
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Renkforce RF100 XL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Renkforce RF100 XL in the language / languages: German as an attachment in your email.

The manual is 7,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Renkforce RF100 XL

Renkforce RF100 XL User Manual - English - 64 pages

Renkforce RF100 XL User Manual - Dutch - 64 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info