692203
27
Zoom out
Zoom in
Previous page
1/64
Next page
27
13. Algemene instructies voor de 3D-print
Schakel tijdens het printproces nooit de stroom uit. Trek de USB-kabel er ook nooit uit en laat de SD-kaart
in het apparaat.
De printkwaliteit van 3D-printers zijn afhankelijk van tal van factoren. De belangrijkste zijn:
- Printsnelheid
- Printlaagdikte
- Printbedkalibratie
- Mondstuktemperatuur
- Temperatuur van de verwarmingsplaat (bij bestelnr. 1592461)
- Filament-intreksnelheid
- 3D-modelstructuur
Het is daarom niet altijd gelijk bij de eerste poging mogelijk, een bevredigend printresultaat te behalen. Correcties
enjnafstemmingenzijnnodigomdeprintkwaliteitteverbeteren.
Elk materiaal heeft andere printinstellingen nodig.
U dient een overhang van meer dan 45° te vermijden. Gebruik indien nodig de bouwplatformoptie in “Cura” en
verwijder het platform na het printproces.
a) Mondstuktemperatuur
Debestemondstuktemperatuurisafhankelijkvanhetlamentmateriaalevenalsvandediktevandeprintlaag.De
printtemperatuurvanhetlamentvarieertafhankelijkvanhetlamentmateriaalendelamentfabrikant.Controleer
vóórhetprintenaltijddeinformatieoverhetbetreffendelament.Omeenzogoedmogelijkresultaattebereiken,
radenwijorigineleRenkforcelamentenaan.
Voer de eerste testprints uit met de standaard temperatuur.
Om de printkwaliteit te optimaliseren, print u hetzelfde objext met dezelfde printlaagdikte en verschillende
spuitmondtemperaturen. Stel telkens een andere temperatuur (in 5 °C-stappen) in als bij het voorafgaande
printproces. Vergelijk vervolgens de printresultaten.
Zovindtuhetmakkelijkstdeoptimalemondstuktemperatuurvoorverschillendelamentenenprintlaagdiktes.
Als de mondstuktemperatuur te heet is ingesteld, kan het materiaal niet snel afkoelen en versmelt weer met de
zich eronder bevindende laag.
Isdemondstuktemperatuurtelaag,wordthetlamentnietvloeibaargenoegenisdelamentstroomniethomogeen.
Bovendienkunnendeafzonderlijkelamentlagennietvoldoendeverbinden.
b) Verhinderen van mondstukblokkades
Houd de hoge temperatuur aan het mondstuk niet te lang op peil zonder te printen.
Houdthetmondstukbijhetintrekkenvanhetlamentopminstens20mmafstandtenopzichtevanhetprintbed.
Verwijderhetlamentnagebruik.
Zorg voor voldoende ventilatie. De ventilatieopeningen aan de extruder mogen niet worden afgedekt.
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Renkforce RF100 XL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Renkforce RF100 XL in the language / languages: Dutch as an attachment in your email.

The manual is 8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Renkforce RF100 XL

Renkforce RF100 XL User Manual - English - 64 pages

Renkforce RF100 XL User Manual - German - 62 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info