569768
48
Zoom out
Zoom in
Previous page
1/51
Next page
Rendama
x
Doc890/3456CV02B 51
The following activities must be carried out (for an extensive description of these activities, see
8.3):
- Renew the ignition and ionisation electrodes
- Clean the air inlet damper
- Clean the fan blades
- Clean the fl ue gas collection chamber
- Clean the condensate trap and the drainage pipe from the appliance
- Clean the gas fi lter
- Inspect all pressure measurement pipes and nipples.
- After removing the panels from the left hand side of the appliance, ignition and burning can be
observed from both front and rear via a sight glass.
- Test the unit at the fl ue gas side for CO
2
and CO and correct these at both full and minimum
capacity if necessary.
- Check all the safety functions, and make any necessary adjustments.
- Measure the water temperature difference ∆T as a measure of the fl ow rate.
- Check the water pressure
- Check the water quality: hardness and chloride content
- Record all data
- Clean the outside of all the panels and ensure that these all have a smart appearance.
8.3 Procedure
a) Disconnect the power supply
b) Close the gas supply valve
- The ignition and ionisation electrodes are fi tted at the rear of the appliance.
- Remove the spark plug caps from the ignition and ionisation electrodes and inspect them for
possible damage, such as indications of burning or pollution (renew the spark plug caps if dam-
aged).
In order to carry out the following activities, the panels must fi rst be removed.
- In order to clean the air inlet damper this must fi rst be re moved. Clean it with a vacuum cleaner.
- For appliances installed in a dusty environment, the fan blades may become dirty. This will
result in the air supply being reduced and the fan becoming unbalanced. Clean the fan blades
with a brush. All loose dirt can be removed in this way.
- A trap is fi tted under the condensate collection tank. Un screw the trap and clean it.
- A gas fi lter is fi tted at the start of the gas train.
This fi lter can be cleaned as follows:
1 Close the gas valve on the boiler
2 Unscrew the six bolts securing the cover to the gas fi lter
3 Carefully remove the fi lter element
4 Clean the fi lter element by shaking it. When it is heavily polluted, the fi lter element must be
renewed.
5 Re-assemble the fi lter
6 Check for leaks (soap solution).
- Inspect all the pressure measurement pipes. Ensure that these are securely fastened and
tighten the connection nuts if necessary.
- Inspect the screws in the measuring nipples; renew the measuring nipples if they have become
damaged.
- In order to measure gas and air pressures and to perform measurements at the fl ue gas side,
calibrated test equipment must be employed.
- All test data must be recorded on the applicable test forms.
8.4 Cleaning the burner and heat exchangers
The burner and the heat exchangers can be cleaned internally with suitable media. For advice
concerning suitable media, consult the service department of your supplier.
48


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rendamax R3400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rendamax R3400 in the language / languages: English as an attachment in your email.

The manual is 1,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info