569768
44
Zoom out
Zoom in
Previous page
1/51
Next page
Rendama
x
Doc890/3456CV02B 47
Setting the fl ow temperature for Domestic Hot Water (cover open)
N.B. Only applicable if the Direct Hot Water function is used with the BM-E expansion module.
- Open the lid
- Turn the rotational switch (pos.5) clockwise until the arrow at the bottom of the LCD display
indicates parameter P2
- Press the combined Reset/Programming key (pos. 3). The LED will light. Turn the rotary switch
(pos.5) until the desired water fl ow temperature has been reached
- Press the combined Reset/Programming key. The LED will go out
- Close the cover.
N.B. The new temperature setting will only become active once the Reset/Programming key has
been released.
6.4 Fault indications
A fault always results in a fl ashing E symbol and a fault code appearing in the display. When a
fault occurs, the cause must always be found and corrected before the related protective function
is reset. If a fault occurs 3 times or more within half an hour, the fault code will be appearing in the
display with an additionally “3” above it. The boiler can be nevertheless in operation.
1 The high limit thermostat has operated. The boiler tempera ture has exceeded 100°C. Press
the reset button.
2/3 The interlocking input has been interrupted. Correct the external error and press reset.
4/5 Ionisation fault. Press reset.
6 Temperature protection has operated. The boiler tempera ture has exceeded the setting.
Press reset.
7 The lockout input has been interrupted. Correct the external fault and press reset.
11 Error in fl ame signal. A fl ame has been detected during start-up. Correct the fault and press
reset.
12 Flow temperature sensor is faulty. Correct fault.
13 Wiring of the CXE/EM extension module is defective. Cor rect fault.
14 Hot water temperature sensor is defective. Correct fault.
15 External temperature sensor is defective.Correct fault.
18 Header temperature sensor is defective. Correct fault.
20 Error in the control of gas valve 1. After burner has stopped a ame has been detected for a
period of 5 seconds. This in spite of the fact that valve 1 is closed. Correct the fault by clean-
ing the valve.
21 Error in the control of gas valve 2. After burner has stopped a ame has been detected for a
period of 5 seconds. This in spite of the fact that valve 2 is closed. Correct the fault by clean-
ing the valve.
22 A i r ow too low. The air pressure switch has not operated. Press reset.
23 The air pressure switch has not switched off. Press reset.
27 The air pressure switch switched off during operation.
30 CRC error in EEprom data group “Boiler. Press reset.
31 CRC error in EEprom data group “Burner. Press reset.
32 Fault in 24 V circuit. Correct fault.
40 Error detected in the position of the fl ow switch. The fl ow switch is tested under two condi-
tions:
- No heat demand - pump stop - fl ow switch must return in rest position.
- Heat demand - pump turns - fl ow switch detects water fl ow.
Not adhering to the above conditions will give the error condition. Correct fault.
X.Y. An internal fault has been detected during the self-test. Press reset.
44


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rendamax R3400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rendamax R3400 in the language / languages: English as an attachment in your email.

The manual is 1,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info