587850
17
Zoom out
Zoom in
Previous page
1/32
Next page
Installation instructions for qualified personnel
Transport the unit in its original
packaging as close as possible
to the installation location.This
avoids transportation damage.
Check that the packaged
contents are complete and
inspect the unit for any visible
signs of transportation damage.
Immediately notify any
deficiencies to the contractual
partner and forwarding agent.
Lift the unit by its corners
and not the refrigerant or
condensation connections.
Insulate the refrigerant pipes
(injection and suction pipe),
valves and connections to make
them tight against vapour
diffusion.If necessary also
insulate the condensation pipe.
Select an installation location
which allows air to freely
flow through the inlet and
outlet.(see section "Minimum
clearances").
Do not install the unit
adjacent to any hotspots.Unit
performance will be impaired if
installed next to hotspots.
Only open the stop valves
for the refrigerant pipes after
installation has been fully
completed.
Use caps or adhesive tape to
seal off the open refrigerant
pipes and prevent the ingress of
humidity.
Never kink or push in the
refrigerant.
Avoid unnecessary bending.
This minimises the pressure
loss in the refrigerant pipes and
ensures that the compressor
oil can flow back without
obstruction.
Special measures concerning
the oil return pipe must be
taken if the outdoor component
is mounted above the indoor
unit.
(See section "Oil return
measures").
Add refrigerant if the basic
length of the refrigerant pipe
exceeds 5 metres.
The amount of additional
refrigerant is given in the
chapter "Adding refrigerant".
Only use the union nuts
supplied with the refrigerant
pipes. These should only
be removed shortly before
connecting the refrigerant
pipes.
Establish all electrical
connections in accordance with
the relevant DIN- and VDE
standards.
Connect the electrical cables
properly to the terminals.
Otherwise there is a risk of fire.
Service openings should be
provided in the suspended
ceiling to allow maintenance
access to the control box.
Any ventilation ducts or pipes
and connection fittings, which
are used to connect a second
room or supply fresh air, should
be insulated with diffusion-tight
material.
Wall breakthroughs
The wall breakthrough must
have a diameter of min. 70 mm
and a fall of 10 mm from inside
to outside for each indoor unit.
We recommend that the
inside of the hole is padded or
lined, e.g. using a PVC tube,
to prevent the pipes being
damaged.
After installation has been
completed, use a suitable
sealing compound to close
off the wall breakthrough
(responsibility of customer).
Do not use cement- or lime-
based materials!
Important points prior to
installation
Control cable
Condensation pipe
Injection pipe
Suction pipe
PVC tube
Pipes and cables in wall breakthrough
17
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for REMKO SV261 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of REMKO SV261 in the language / languages: English as an attachment in your email.

The manual is 3,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of REMKO SV261

REMKO SV261 User Manual - German - 32 pages

REMKO SV261 User Manual - Dutch - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info