726815
8
Zoom out
Zoom in
Previous page
1/24
Next page
3 Product description
Information about assembly and installation can be
found on the following pages of the operating
manual. Information on operating the REMKO
Smart Control T
ouch remote control can be found
in the "REMKO Smart-Control Touch" operating
manual. This remote control gives you options for
setting and querying the relevant parameters of the
REMKO heat pump at the user and expert levels.
All setting procedures overwrite the existing set-
tings on the heat pump controller. Either for a
defined heating circuit or parameters for the entire
system. The specific information for operating the
remote control at the "User" level can be found in
the "REMKO Smart Control Touch" manual. You
will find that operation is intuitive and logical. The
parameters relevant to specialists are enabled at
the "expert level" and are only intended for spe-
cialist personnel. It contains all the information
required for installation and commissioning of the
remote control by REMKO Service or the installer.
The remote control has the same parameters as
the regulation system in the heat pump. Assembly
should take place in a reference room such as the
living room where there is easy access. The
REMKO room sensor can be used to determine
the current room temperature and air humidity.
Since you have full access to all the parameters of
the installed heat pump via the remote control, it
cannot be used in so-called tenant mode. A WLAN
function is available via the installed WLAN stick as
standard. This gives you the option of connecting
your remote control to the in-house WiFi-enabled
router and your smartphone. A description of this
function can be found on the following pages.
The following examples for connecting the
REMKO remote control require software ver
-
sion 4.26. If the software is not up to date,
updating to software version 4.26 or later must
be carried out!
4 Electrical wiring and
interfaces
12V GND
802.11n
1
2
3
Fig. 1: Electrical wiring and interfaces
1
Network cable connection (LAN cable)
2
Power supply connection
(12V/GND)
For the surface-mounted installation, the trans-
former included in the scope of delivery is used for
the power supply (230V~ / 12V
). If the unit is
flush-mounted, a 12V direct current source must
be provided at the installation position.
3
WiFi receiver (WLAN stick)
The available WiFi receiver is required if a wireless
network connection is to be used.
REMKO Smart-Control Touch
8
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for REMKO Smart-Control Touch at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of REMKO Smart-Control Touch in the language / languages: English as an attachment in your email.

The manual is 2,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of REMKO Smart-Control Touch

REMKO Smart-Control Touch User Manual - German - 24 pages

REMKO Smart-Control Touch User Manual - Dutch - 24 pages

REMKO Smart-Control Touch User Manual - French - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info