587572
7
Zoom out
Zoom in
Previous page
1/16
Next page
7
Operating Mode
Cooling
1. Switch the unit on with the "On / Off” button.
2. Set the target temperature using the arrow buttons.
3. Select the fan setting (AUTO, HI, MED or LO) with
the "MODE" button.
Ventilation (circulation)
1. Switch the unit on with the "On / Off” button.
2. Set the FAN operating mode with the "MODE” but-
ton.
3. Please note: in circulation mode, the outdoor unit
can remain in the room. But do not attach the out-
door unit to the indoor unit.
Dehumidifying
Set up the indoor unit and the outdoor unit in the room
to be dehumidified.
1. Make sure that the indoor unit is not drawing in
warm air from the outdoor unit.
2. Do not attach the outdoor unit to the indoor unit.
3. Please note: the condensation which forms during
dehumidifying may not be pumped to the outdoor
unit because otherwise it would be expelled to the
air in the room or would drip out of the outdoor unit.
4. Remove the water tank drainage tube from the back
of the indoor unit from its holder and remove the
sealing cap.
5. Guide the condensation at an incline to a drain or a
container.
Fig. 5
1
2
5
6
4
POWER
on / off
TIMER
reset
AUTO
SWING
MODE
set
THERMO
CONTROL
*
Make sure that the lower edge of the outdoor unit
is 1.8 meters above the lower edge of the indoor
unit.
*
Make sure that the external container does not
overflow!
This may cause water damage.
10 Operating mode and fan setting display
This display provides information about the operat-
ing mode and the fan setting which have been se-
lected.
11 "DRAIN WATER" display (Water tank full)
When the water tank is full, the "DRAIN WATER" and
"MODE" displays blink and an alarm goes off. The
compressor automatically switches off. After the wa-
ter tank has been emptied and replaced, the unit
switches back to automatic operation.
Information about the water tank:
During normal operation, the water tank will not fill up
because the condensation is pumped out of the tank via
the connecting line to the outdoor unit.
Infrared-remote Control
All settings can also be made using an infrared remote
control (optional with RKL 460).
A description of the button functions (see picture below)
can be found in the “Control panel” section. The remote
control’s range is approximately 5 m.
Power is provided by two 1.5 V AAA batteries. (supplied
with the remote control)
6. Switch the unit on with the On / Off button.
7. Set the unit to the lowest target temperature with the
temperature selector button.
20°C.
8. Using the MODE button, set the lowest fan speed.
LO.
The water tank must be emptied when fixing malfunc-
tions.
Proceed as follows:
1. Remove the water tank drainage tube on the back of
the indoor unit from its holder.
2. Remove the sealing cap from the tube.
3. Collect the water that drains out.
4. Then reinsert the sealing cap into the tube.
5. Replace the tube into its holder.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for REMKO RKL470 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of REMKO RKL470 in the language / languages: English as an attachment in your email.

The manual is 0,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of REMKO RKL470

REMKO RKL470 User Manual - German - 16 pages

REMKO RKL470 User Manual - German - 16 pages

REMKO RKL470 User Manual - Dutch - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info