587720
17
Zoom out
Zoom in
Previous page
1/24
Next page
200
120
1500
120
120
Air intake
Air outlet
Installation instructions for qualified personnel
Important points prior to
installation
Minimum clearances
Observe the minimum clearances
to allow access for maintenance
repair work and for optimum air
distribution.
Minimum clearances
All values in mm
Connection variations
The following connection
variations for the refrigerant,
condensation and control lines can
be utilized.
Connection variations
1 Outlet on the wall, right
2 Outlet through the wall, right
3 Outlet through the wall, left
4 Outlet on the wall, left
1234
For installation of the entire
system, observe the operating
instructions of the indoor unit and
the outdoor unit.
■
Transport the unit in its original
packaging as close as possible
to the installation location. This
avoids transportation damage.
■
Check the contents of the
packaging for completeness
and check the unit for visible
transport damage.
Immediately notify any
deficiencies to the contractual
partner and forwarding agent.
■
Lift the unit at the corners
and not by the refrigerant or
condensation connections.
■
The refrigerant pipes (injection
and suction pipe), valves and
connections to make them
tight against vapour diffusion.
If necessary, also insulate the
condensation line.
■
Select an installation location
which allows air to freely
flow through the inlet and
outlet (see section "Minimum
clearances")
■
Do not install the unit in
the immediate vicinity of
devices with intensive thermal
radiation. Installation near
sources of thermal radiation
reduces the output of the unit.
■
Install the refrigerant pipes from
the indoor unit to the outdoor
unit.
■
Seal off open refrigerant pipes
with suitable caps or adhesive
strips to avoid the infiltration
of moisture and never kink or
compress the refrigerant pipes.
■
Only use the union nuts for the
refrigerant pipes included in
the delivery, and remove them
shortly before connecting the
refrigerant pipes.
■
Establish all electrical
connections connections in
accordance with the relevant
DIN- and VDE standards.
■
See electrical connection
diagram Ensure the electrical
cables are properly connected
to the terminals, otherwise
there is a risk of fire.
Installation material
The indoor unit is fastened using
4 threaded rods (provided by the
customer) over a wall brace.
Selection of the installation
location
The indoor unit is designed for
horizontal wall installation above
doors.
However, it can also be used in
the upper wall area (min. 1.75 m
above the floor).
There is an approx. 50 cm
long pipe permanently
installed from right to left in
the indoor unit. This is to be
taken into consideration when
undertaking preinstallation
work on site.
NOTE
17
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for REMKO MXW200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of REMKO MXW200 in the language / languages: English as an attachment in your email.

The manual is 1,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of REMKO MXW200

REMKO MXW200 User Manual - German - 24 pages

REMKO MXW200 User Manual - Dutch - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info