587594
14
Zoom out
Zoom in
Previous page
1/24
Next page
14
Assembly Instructions for
Service Personnel
Important instructions prior to installation
Ensure that the contents of the package are com-
plete and that the units have no visible damage re-
sulting from transport. Any problems must be com-
municated directly to your contract partner and the
shipping company.
Subsequent complaints will not be acknowledged.
Place the unit in its original packaging as close as
possible to the location where it will be assembled to
prevent damage from transport.
Prior to installation, check that the electrical connec-
tion values and the data on the type plate are
consistent.
Do not install the unit in the direct vicinity of objects
that emit intense heat.
Lights, etc.
Select a location to set up the unit where air can flow
freely in and out of the device.
Observe minimum distance.
Only use the swivel nuts supplied for the refrigerant
pipes. Other components can damage the thread.
Remove the protective caps of the unit connections
just before connecting the refrigerant pipes.
Make sure that the maximum length of 10 or 15 me-
ters for the refrigerant pipes is not exceeded and the
difference in height to the unit is not more than 5 or
8 meters.
The refrigerant pipes may not be bent or pressed.
Make sure that all refrigerant pipes including all con-
nectors and valves are insulated against heat and
sealed against diffusion.
Only add additional refrigerant to the system if the
length of the refrigerant pipes exceeds 5 meters.
See the “Adding refrigerant” section for the addi-
tional refrigerant amounts.
The condensation pipe must be placed at an incline
of at least 2%.
If this pipe is connected to a sewage pipe, an odour
seal must be installed the upper edge of which
may not extend beyond the lower edge of the indoor
unit.
All electrical connections must meet the relevant re-
quirements. The power supply is only connected to
the outdoor unit.
The control line to the indoor units should be laid at the
same time as the refrigerant pipes.
Make sure that the electrical lines have been prop-
erly attached in the electrical terminals.
The indoor unit and outdoor unit of the REMKO air-
conditioner have been adjusted to one another from
a technical standpoint.
The guarantee becomes null and void if third-party
components are used.
Remember that when installing and maintaining air
conditioners, high-pressure refrigerant pipes and
electrical current can pose hazards.
During unit operation, some components in the cool-
ing cycle can reach temperatures of more than
70°C.
Be especially careful when covers are removed.
Preventable installation mistakes
Make absolutely sure to follow the instructions below
when installing the indoor unit:
Place the pipes between the indoor unit and the out-
door unit and keep the length of the refrigerate pipes
as short as possible.
The shut-off valve of the refrigerant pipes may only
be opened once installation is complete.
Always secure electrical lines properly in the electri-
cal terminals.
Not doing so could cause a fire.
Seal open refrigerant pipes with suitable caps and/or
adhesives to prevent moisture penetration.
Avoid bending the pipes unnecessarily.
This minimises pressure loss in the refrigerant pipes
and guarantees that the compressor oil can flow
freely.
If the outdoor unit is mounted above the indoor unit,
you must take steps to recirculate the oil.
See section on oil recirculation.
Do not set up the unit in the direct proximity of de-
vices that emit intense heat, such as glass reflection
surfaces.
If the unit is assembled close to heat emissions, the
amount of warm air expelled by the plate fins of the out-
door unit is reduced.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for REMKO ML680 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of REMKO ML680 in the language / languages: English as an attachment in your email.

The manual is 1,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of REMKO ML680

REMKO ML680 User Manual - German - 28 pages

REMKO ML680 User Manual - Dutch - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info