587704
4
Zoom out
Zoom in
Previous page
1/32
Next page
Safety notes
Disposal of packaging
All products are packed for
transport in environmentally
friendly materials. Make a valuable
contribution to reducing waste
and sustaining raw materials.
Only dispose of packaging at
approved collection points.
Disposal of equipment
and components
Only recyclable materials are used
in the manufacture of the devices
and components,
Help protect the environment
by ensuring that the devices
or components (for example
batteries) are not disposed in
household waste, but only in
accordance with local regulations
and in an environmentally safe
manner, e.g. through authorised
disposal and recycling specialists or
at collection points.
Warranty
Prerequisite for any warranty claims
are that the purchaser or their
customer has completely filled out
the "warranty registration card"
and commissioning report included
with the unit at the time when the
equipment was purchased and first
put into operation and returned it
to REMKO GmbH & Co. KG.
The warranty conditions are
listed in the "General Business
and Delivery Conditions". Only
the contractual parties can strike
special agreements beyond these
conditions. For this reason please
first contact your direct contractual
partner.
Environmental
protection
and recycling
Carefully read this manual before
putting commissioning the
equipment. It provides useful
tips and information as well as
hazard warnings to prevent injury
or material damage . Failure to
follow the directions in this manual
can result in endangerment to
persons, the environment and the
equipment itself and will void any
claims for liability.
Keep this manual and the
refrigerant datasheet near the
unit.
The unit may only be set up and
installed by qualified personnel.
The setup, connection and
operation of the unit and
its components must be in
accordance with the operating
conditions stipulated in this
manual and comply with all
applicable local regulations.
Mobile units must be set up
securely on suitable surfaces and
in an upright position. Stationary
units must be permanently
installed for operation.
Modification of equipment
and components supplied by
REMKO is not permitted and
can cause malfunctions.
Equipment and components
may not be operated in areas
where there is an increased
risk of damage. Observe the
minimum clearances.
The electrical voltage supply
is to be adapted to the
requirements of the equipment.
The operational safety of
equipment and components is
only assured if they are used as
intended and fully assembled.
Safety devices may not be
modified or bypassed.
Do not operate equipment
or components with obvious
defects or signs of damage.
All housing parts and openings,
e.g. air inlets and outlets, must
be free of foreign objects, fluids
or gases.
The equipment and components
must be kept an adequate
distance from flammable,
explosive, combustible,
aggressive and dirty areas or
atmospheres.
Touching equipment parts can
result in burns or injury.
Installation, repair and
maintenance work may only
be carried out by authorised
specialists. Visual inspections
and cleaning can be performed
by the operator as long as the
equipment is not under voltage.
Take appropriate hazard
prevention measures when
performing installation, repair or
maintenance work or cleaning
the equipment.
The equipment or components
are not to be exposed to any
mechanical stresses, extreme
levels of humidity or direct
sunlight.
Intended use
Depending on the model, the
equipment and the additional
fittings with which it is equipped
is only intended to be used as an
air-conditioner for the purpose of
cooling or heating the air in an
enclosed room.
Different or additional use shall not
be classed as intended use. The
manufacturer/supplier assumes no
liability for damages arising from an
unintended use of the equipment.
The user bears the sole risk in such
cases.
Using the equipment as intended
also includes working in accord-
ance with the operating manual
and installation instructions and
complying with the maintenance
requirements.
REMKO ML...DC - ARCTIC
4
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for REMKO ML352 DC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of REMKO ML352 DC in the language / languages: English as an attachment in your email.

The manual is 1,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of REMKO ML352 DC

REMKO ML352 DC User Manual - German - 32 pages

REMKO ML352 DC User Manual - German - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info