587699
16
Zoom out
Zoom in
Previous page
1/28
Next page
Selecting the installation
location
Indoor unit
The indoor unit is designed for
horizontal wall-mounting above
doors. It can also be fitted high up
on walls (min. 1.75 m above the
level of the floor).
Outdoor component
The outdoor component is
designed for horizontal free-
standing use in outdoor areas. It
should be placed on level, flat and
firm ground. The unit should also
be secured to prevent toppling.
The outdoor unit can be installed
both inside and outside buildings.
In the case of outdoor installation,
please follow the instructions given
below to protect the unit against
the weather.
Wall breakthroughs
The wall breakthrough must
have a diameter of min. 70 mm
and a fall of 10 mm from inside
to outside.
We recommend that the
inside of the hole is padded or
lined, e.g. using a PVC tube,
to prevent the pipes being
damaged.
After installation has been
completed, use a suitable
sealing compound to close
off the wall breakthrough
(responsibility of customer). Do
not use cement- or lime/based
materials!
Installation material
The indoor unit is fastened using
4 screws and a wall bracket. The
screws should be provided by the
customer.
The outdoor component is
fastened to the wall or ground
using 4 screws and a wall or floor
bracket.
Minimum clearance to snow
20 cm
Snow
Windbreak
Wind
Pipes and cables in wall breakthrough
Control cable
Condensation pipe
Injection pipe
Suction pipe
PVC tube
Rain
The unit should be at least 10 cm
off the ground when mounted on
the roof or ground. An optional
floor bracket is available as an
accessory.
Sun
The liquefier on the outdoor
component radiates heat. Exposure
to direct sunlight will further
increase the temperature of the
fins and reduce the heat output
of the finned heat exchanger.
The outdoor component should
therefore be installed as near
as possible to the north side of
the building. If necessary, take
measures to provide sufficient
shade (responsibility of customer).
One possible solution is to build a
small roof. These measures should
not affect the flow of warm outlet
air.
Wind
If the unit is being installed in
windy areas, ensure that the
warm outlet air discharges in the
main wind direction. If this is not
the case it may be necessary to
install a windbreak (provided by
the customer). Ensure that the
windbreak does not adversely
affect the air intake to the unit.
Snow
The unit should be wall-mounted
in areas of heavy snowfall.
Installation should be at least
20 cm above the expected level
of snow to prevent snow from
entering the outdoor component.
An optional wall bracket is
available as an accessory.
REMKO ML
16
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for REMKO ML 351 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of REMKO ML 351 in the language / languages: English as an attachment in your email.

The manual is 4,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of REMKO ML 351

REMKO ML 351 User Manual - German - 28 pages

REMKO ML 351 User Manual - Dutch - 28 pages

REMKO ML 351 User Manual - French - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info