587698
4
Zoom out
Zoom in
Previous page
1/28
Next page
Safety notes
Disposal of packaging
All products are carefully packaged
using environmentally friendly
materials prior to transportation.
Make a valuable contribution to
reducing waste and sustaining
raw materials. Only dispose of
packaging at approved collection
points.
Disposal of
old equipment
Equipment manufacture is subject
to continuous quality control. Only
high-quality materials are used, the
majority of which can be recycled.
Help protect the environment by
only disposing of old equipment in
accordance with local regulations
and in an environmentally safe
manner, e.g. through authorised
disposal and recycling specialists or
at collection points.
Warranty
In order to make warranty claims,
it is essential that the the ordering
party or their representative
complete and return the "certificate
of warranty" and commissioning
report to REMKO GmbH & Co. KG
at the time when the equipment
was purchased and commissioned.
The warranty conditions are
detailed in the "General terms
and conditions“. The contractual
parties can also agree additional
terms beyond the scope of the
above. In this case, first contact the
contractual partner.
Environmental
protection
and recycling
Carefully read this manual before
starting the unit for the first time. It
contains useful tips and notes as
well as hazard warnings to prevent
injury or material damage . Non-
observance of this manual may
endanger persons, the environment
as well as the equipment itself and
will void any claims for liability.
Store this manual and the
refrigerant datasheet in the
vicinity of the unit.
The unit should only be set
up and installed by qualified
personnel.
The setup, connection and
operation of the unit and
its components must be in
accordance with the operating
conditions stipulated in this
manual and comply with all
applicable local regulations.
Units designed for mobile use
should be safely set up on a
suitable floor and in a vertical
position. Units designed for
stationary use should only be
operated in their permanently
installed state.
It is prohibited to make
modifications or changes to
equipment or components
supplied by REMKO as this may
cause malfunctions.
Equipment and components
should not be operated in areas
where there is a heightened
damage risk. Observe the
minimum clearances.
The electrical supply should
be adapted to fulfil the
requirements of the unit.
The operational safety of
equipment and components is
only assured providing they are
used as intended and in a fully
assembled state. Safety devices
should not be modified or
bypassed.
Do not operate equipment
or components with obvious
defects or signs of damage.
All housing parts and openings,
e.g. air inlets and outlets, must
not be blocked by foreign items,
fluids or gases.
The equipment and components
must be kept a safe distance
from inflammable, explosive,
combustible, agressive and dirty
areas or atmospheres.
Persons coming into contact
with equipment parts may suffer
burns or injury.
Installation, repair and
maintenance work should only
be carried out by authorised
specialists. Inspection and
cleaning can be performed
by the operator providing the
equipment is not under voltage.
Take appropriate hazard
prevention measures when
performing installation, repair or
maintenance work or cleaning
the equipment.
The equipment and components
should not be exposed to any
mechanical stresses, extreme
levels of humidity or direct
exposure to sunlight.
REMKO ML
4
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for REMKO ML 261 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of REMKO ML 261 in the language / languages: English as an attachment in your email.

The manual is 4,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of REMKO ML 261

REMKO ML 261 User Manual - German - 28 pages

REMKO ML 261 User Manual - Dutch - 28 pages

REMKO ML 261 User Manual - French - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info