587590
22
Zoom out
Zoom in
Previous page
1/32
Next page
Condensation connection - outdoor unit
Opening for
condensation
connection
Condensation pan of
outdoor component
Condensation connection
All electrical installation work
should be performed by spe-
cialist contractors. Isolate the
voltage supply when connect-
ing the electrical terminals.
CAUTION
Electrical connection
Mains cable must be installed as
voltage supply to the indoor unit
and a control cable to the outdoor
component, with appropriate
safeguards.
Condensation
connection
Due to the dew point shortfall,
condensation forms on the
evaporator during the cooling
operation and on the liquefier
during heating operation.
Below the evaporator is a catch
pan, which must be connected
with a drain.
The lower part of the outdoor
component housing is formed in
the shape of a collection tray. The
condensate connection included
in the scope of delivery is to be
attached here.
■
The condensation pipe should
have a fall of min. 2 %.
(Fig. 10).
If necessary, fit vapour diffusion
tight insulation.
■
The condensation pipe from
the unit should run freely
into the drainage pipe. If the
condensation runs directly
into a sewer pipe, fit a trap to
prevent any unpleasant odours.
The condensation hose is designed
to be installed on the left side
(view from front).
10
Fall of condensation pipe
minimum
2% fall
■
When operating the unit at
ambient temperatures below
0 °C , make sure to route the
condensation pipe freeze proof.
The lower part of the housing
is also to be kept frost free by
the customer, in order to ensure
permanent draining of the
condensate.
If necessary, fit supplementary
pipe heating.
■
After completed routing, check
for unobstructed condensation
discharge and ensure that a
permanent seal is provided.
Connecting the indoor unit
■
We recommend installing a
master / repair switch on the
building near the indoor unit.
■
Voltage is supplied to the
indoor unit, the outdoor unit
is supplied through the control
cable from the indoor unit to
the outdoor unit.
■
The terminal blocks for making
the connections are located on
the front of the unit. When the
unit is installed, measurements
can be made from the front by
removing the cover.
The device's scope of delivery
includes a five metre long, four-
core control cable for connecting
the indoor unit to the outdoor
component. The control cable to
the outdoor component contains
a data line which serves to realise
communication between the
indoor unit and the outdoor
component. This is used for
controlling the cooling and heating
performance and for forwarding
fault indications to the indoor unit.
REMKO MD
22
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for REMKO MD261 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of REMKO MD261 in the language / languages: English as an attachment in your email.

The manual is 1,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of REMKO MD261

REMKO MD261 User Manual - German - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info