726832
22
Zoom out
Zoom in
Previous page
1/40
Next page
Installing duct components
The duct components are connected to each other
and to the unit with 4 screws each. The duct com-
ponents must be installed in such a way that they
do not exert any tension on the unit or on the rest
of the duct system. The following points must also
be observed:
nAll duct surfaces must be adequately insulated
against condensation water on site
nIf necessary, all joints must be sealed with suit-
able sealants provided by the customer
nThe effective duct cross-section must not be
reduced
nThe pressure losses on the air side and the
resulting power losses must be kept as low as
possible
Fig. 14: Installation of duct components
6 Installation
6.1 Unit installation
Ceiling installation
NOTICE!
Installation and commissioning should only be
performed by trained specialists.
NOTICE!
If the unit is not mounted positively, vibration
can occur.
The unit is attached by means of mounting holes in
the housing while also taking account of the air
outlet side directed towards the centre of the room.
1. Mark the mounting points according to the
mounting's dimensions on structurally
acceptable building components and secure
the unit
2. Check again that the unit is level
3. Connect the medium pipes, electrical cables
and condensate drainage line to the unit as
described below
Selecting the hydraulic connection
2-conductor cooling system
Wall installation without valve assembly:
when the fan is switched off the flow of air from the
air inlet can be ignored without sacrificing comfort.
In this application case, use of a valve assembly is
not absolutely essential.
Ceiling installation without valve assembly:
a valve assembly must be used in this application
case to prevent the flow of cold air from the air
outlet when the fan is switched off.
Wall installation with valve assembly:
in order to prevent any flow of cold air and severe
condensate formation, for reasons of comfort a
valve assembly can be used in this application
case.
Ceiling installation with valve assembly:
in order to prevent any flow of cold air and perma-
nent flow-generated noise, for reasons of comfort a
valve assembly is recommended in this application
case.
REMKO KWK ZW series
22
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for REMKO KWK ZW serie at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of REMKO KWK ZW serie in the language / languages: English as an attachment in your email.

The manual is 2,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of REMKO KWK ZW serie

REMKO KWK ZW serie User Manual - German - 40 pages

REMKO KWK ZW serie User Manual - Dutch - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info