726832
18
Zoom out
Zoom in
Previous page
1/40
Next page
5 Installation instructions
for qualified personnel
Important notes prior to installation
Observe the Operating Manuals for the indoor unit
and the chiller or heating system or the heat pump
system when installing the entire system.
nThe indoor units and chillers work independ-
ently. A connecting line between the two is not
necessary.
nTransport the unit in its original packaging as
close as possible to the installation location.
You avoid transport damage by doing so.
nCheck the contents of the packaging for com-
pleteness and check the unit for visible trans-
port damage. Report any damage immediately
to your contractual partner and the shipping
company.
nSelect an installation location which allows air
to freely flow through the air inlet and outlet
(see section "Minimum clearances").
nDo not install the unit in the immediate vicinity
of devices which generate intensive thermal
radiation. Installation in the vicinity of thermal
radiation reduces the unit output.
nLift the unit at the corners and not by the
medium or condensate drainage connections.
nThe medium connection lines, valves and con-
nections must have vapour density insulation.
If necessary also insulate the condensate
drainage line. In dual systems with cooling and
heating modes, the requirements of the current
energy savings ordinance (EnEV) are to be
complied with.
nSeal off open refrigerant piping with suitable
caps or adhesive strips to prevent the infiltra-
tion of moisture and never kink or compress
the refrigerant piping.
nAvoid unnecessary bends. This minimises the
pressure loss in the lines.
nInstall all electrical wiring in accordance with
applicable DIN and VDE standards.
nEnsure the electrical cables are properly con-
nected to the terminals. Otherwise there is a
risk of fire.
nOnly install the valve assembly or other attach-
ments once the indoor unit has been installed.
Installation material
The indoor unit is attached using 4 bolts to be pro-
vided by the customer.
Selecting the installation location
Wall / ceiling unit
The indoor unit is designed for vertical wall installa-
tion, for instance underneath windows. However, it
can also be used in the upper wall area (max. 1.25
m above floor level).
The unit is also designed for horizontal ceiling
installation. In this case particular attention must
be paid to the condensate drainage (see the
Chapter "Condensate drainage connection").
Connection variants
The following connection variants can be used for
the medium and condensate pipes and the control
lines.
AB
Fig. 10: Connection variants
A: Outflow, left
B: Outflow, right
REMKO KWK ZW series
18
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for REMKO KWK ZW serie at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of REMKO KWK ZW serie in the language / languages: English as an attachment in your email.

The manual is 2,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of REMKO KWK ZW serie

REMKO KWK ZW serie User Manual - German - 40 pages

REMKO KWK ZW serie User Manual - Dutch - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info